Return To Restaurant Listing | Return to Environmental Health Homepage

Facility: Save Mart #102
Address: 1701 Bellevue Road, Atwater, CA

The most recent inspection of this food facility resulted in a rating of
Good (Total Points: 5.00)
0-6  Points: Good
7-13 Points: Satisfactory
14+  Points: Unsatisfactory
Rating on date 5-11-2021: Good (Total Points: 5.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
5-11-2021 Wiping cloths used to wipe service counters, scales or other surfaces that may come into contact with food shall be used only once unless kept in clean water with sanitizer. (114135, 114185, 114185.1, 11485.2, 114185.3) 2.00 Cloths used to wipe service counters, scales, and other surfaces that may directly or indirectly contact food shall be used only once until laundered or may be used repeatedly if held in a sanitizing solution, as described below. Cloths used with raw foods of animal origin shall be used only once until laundered or may be used repeatedly if kept in a separate container of sanitizing solution, as described below:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with the manufacturer's use directions.
REPEAT VIOLATION) Observed lack of detectable sanitizer residue of sufficient strength in the sanitizer solution buckets used to store wiping cloths. Store all wiping cloths in sanitizer solution of at least 100PPM of Chlorine or 200PPM of Quaternary ammonia. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
5-11-2021 The walls / ceilings shall have durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair. (114065, 114067, 114069, 114175, 114143, 114257, 114259.2, 114266, 114268, 114268.1, 114271, 114272) 1.00 All food facilities shall be kept clean, fully operative, and in good repair. Floor surfaces in all areas in which food is prepared, packaged or stored, where any utensil is washed, where refuse or garbage is stored, where janitorial facilities are located, and in all restrooms and hand washing areas shall be smooth and of durable construction and made from non absorbent material that is easily cleanable.

Each permanent food facility shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. Food facilities that are not fully enclosed on all sides and that are in operation on January 1, 1985, shall not be required to meet the requirements of this section until the facility is remodeled or has a significant menu change or a change in its method of operation. Full enclosure is not required for dining areas and certain other areas when approved for outdoor food services.
Observed the coving near the deep fryer area is damaged/grooved. Repair so flooring is flushed, smooth, and easily cleanable. Work order has already been placed. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
5-11-2021 Any food is misbranded if its labeling is false or misleading, if it is offered for sale under the name of another food, or if it is an imitation of another food for which a definition and standard of identity has been established by regulation. (114087, 114089, 114089.1(a, b), 114090, 114093.1, 114377) 2.00 Present all food in a way that does not mislead or misinform consumers. Food or color additives, colored overwraps, lights or other misleading artificial means shall not be used to misrepresent the true appearance, color, or quality of a food.

The label shall contain the following information:
(1) The common name of the food.
(2) A list of ingredients in descending order of predominance by weight.
(3) The weight, count, or volume.
(4) The name and place of business of the manufacturer, packer, or distributor.
Nutrition labeling may also be required, and must be included when it is available from the manufacturer.

Food facility's or manufacturer's dating information, such as date codes or "use by" statements on packaging may not be concealed or altered.
(REPEAT VIOLATION) Observed some prepackaged items lacking a required label on them. These items include cut melons, and donuts. Provide a label on all prepackaged items that are packaged at the facility. See corrective text for proper label requirements. 0114 RETAIL MARKET 30,001+ SQFT


Rating on date 4-07-2021: Unsatisfactory - reinspection required (Total Points: 17.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
4-07-2021 An accurate easily readable metal probe thermometer suitable for measuring temperature of food shall be available to the food handler. A thermometer +/- 2°F shall be provided for each hot and cold holding unit of potentially hazardous foods and high temperature warewashing machines. (114157, 114159) 1.00 Have a thermometer accurate to within 2°F or 1°C in each hot and cold holding unit. Have a metal probe type thermometer readily available on premises (to all appropriate staff) that is calibrated in accordance with the manufacturer's specifications as necessary to ensure accuracy. Observed the lack of a valid/working thermometer in the cake display unit. Failure to have a readily visible thermometer affixed to the warmest part of the refrigeration unit. Provide a thermometer in all units that hold potentially hazardous food items. 0125 BAKERY
4-07-2021 Exhaust hoods shall be provided to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6" beyond all cooking equipment. All areas shall have sufficient ventilation to facilitate proper food storage. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. (114149, 114149.1) Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields. (114149.2, 114149.3, 114252, 114252.1) 1.00 All areas shall have sufficient ventilation to facilitate proper food storage and to provide a reasonable condition of comfort for each employee, consistent with the job performed by the employee.

Light fixtures in areas where food is prepared, open food is stored, or utensils are cleaned shall be of shatterproof construction or shall be protected with shatterproof shields and shall be readily cleanable. In every room and area in which any food is prepared, manufactured, processed, or prepackaged, or in which equipment or utensils are cleaned, sufficient natural or artificial lighting shall be provided to produce the following light intensity, while the area is in use:
(a) At least 10-foot candles for the following:
(1) At a distance of 30 inches above the floor, in walk-in refrigeration units, and dry food storage areas.
(2) At a working surface on which alcoholic beverages are prepared or where utensils used in the preparation or service of alcoholic beverages are cleaned.
(3) Inside equipment, such as reach-in or under-the-counter refrigerators.
(b) At least 20-foot candles for the following:
(1) At a surface where food is provided for consumer self-service or where fresh produce or prepackaged foods are sold or offered for consumption.
(2) In server stations where food is prepared.
(3) At a distance of 30 inches above the floor in areas used for handwashing, warewashing, and equipment and utensil storage, and in toilet rooms.
(c) Except in server stations where food is prepared, at least 50-foot candles at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor.
Observed the lack of a shatterproof light cover in the cake display fridge. Light fixtures in area where food is prepared, open food is stored, or utensils are cleaned shall be of shatterproof construction or shall be protected with shatterproof shields and shall be readily cleanable. Provide. 0125 BAKERY
4-07-2021 The walls / ceilings shall have durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair. (114065, 114067, 114069, 114175, 114143, 114257, 114259.2, 114266, 114268, 114268.1, 114271, 114272) 1.00 All food facilities shall be kept clean, fully operative, and in good repair. Floor surfaces in all areas in which food is prepared, packaged or stored, where any utensil is washed, where refuse or garbage is stored, where janitorial facilities are located, and in all restrooms and hand washing areas shall be smooth and of durable construction and made from non absorbent material that is easily cleanable.

Each permanent food facility shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. Food facilities that are not fully enclosed on all sides and that are in operation on January 1, 1985, shall not be required to meet the requirements of this section until the facility is remodeled or has a significant menu change or a change in its method of operation. Full enclosure is not required for dining areas and certain other areas when approved for outdoor food services.
Observed the flooring near the deep fryer area is damaged/grooved. Repair so flooring is flushed, smooth, and easily cleanable. Work order has already been placed. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
4-07-2021 The premises of each food facility shall be kept clean and free of litter and rubbish; all clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept free of vermin. (114067 (j), 114123, 114143 (a) & (b), 114175, 114178, 114185, 114185.1, 114185.2, 114185.3, 114185.4, 114256, 114256.1, 114256.2, 114256.4, 114257, 114257.1, 114259, 114259.1, 114259.2, 114259.3, 114279, 114281, 114282) 1.00 All food facilities shall be kept clean, fully operative, and in good repair. A food facility shall at all times be so constructed, equipped, maintained, and operated as to prevent the entrance and harborage of animals, birds, and vermin, including, but not limited to, rodents and insects. The premises of each food facility shall be kept clean and free of litter, rubbish, and vermin.

Lockers or other suitable facilities shall be provided and used for the orderly storage of employee clothing and other possessions. Lockers or other suitable facilities shall be located in a designated room or area where contamination of food, equipment, utensils, linens, and single-use articles cannot occur. Dressing rooms or dressing areas shall be provided and used by employees if the employees regularly change their clothes in the facility.
Observed the use of a stick fly trap in the facility. Remove and discontinue practice. All Fly traps must be food save and fully enclosed. Trap was removed during the inspection. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
4-07-2021 Exhaust hoods shall be provided to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6" beyond all cooking equipment. All areas shall have sufficient ventilation to facilitate proper food storage. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. (114149, 114149.1) Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields. (114149.2, 114149.3, 114252, 114252.1) 0.00 All areas shall have sufficient ventilation to facilitate proper food storage and to provide a reasonable condition of comfort for each employee, consistent with the job performed by the employee.

Light fixtures in areas where food is prepared, open food is stored, or utensils are cleaned shall be of shatterproof construction or shall be protected with shatterproof shields and shall be readily cleanable. In every room and area in which any food is prepared, manufactured, processed, or prepackaged, or in which equipment or utensils are cleaned, sufficient natural or artificial lighting shall be provided to produce the following light intensity, while the area is in use:
(a) At least 10-foot candles for the following:
(1) At a distance of 30 inches above the floor, in walk-in refrigeration units, and dry food storage areas.
(2) At a working surface on which alcoholic beverages are prepared or where utensils used in the preparation or service of alcoholic beverages are cleaned.
(3) Inside equipment, such as reach-in or under-the-counter refrigerators.
(b) At least 20-foot candles for the following:
(1) At a surface where food is provided for consumer self-service or where fresh produce or prepackaged foods are sold or offered for consumption.
(2) In server stations where food is prepared.
(3) At a distance of 30 inches above the floor in areas used for handwashing, warewashing, and equipment and utensil storage, and in toilet rooms.
(c) Except in server stations where food is prepared, at least 50-foot candles at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor.
Observed the lack of a shatterproof light cover in the deli display fridge. Light fixtures in area where food is prepared, open food is stored, or utensils are cleaned shall be of shatterproof construction or shall be protected with shatterproof shields and shall be readily cleanable. Provide. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
4-07-2021 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 2.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method.
(REPEAT VIOLATION) Observed lack of detectable sanitizer residue of sufficient strength in the sanitizer solution buckets used to store wiping cloths. Store all wiping cloths in sanitizer solution of at least 100PPM of Chlorine or 200PPM of Quaternary ammonia. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
4-07-2021 The potable water supply shall be protected with a backflow or back siphonage protection device, as required by applicable plumbing codes. (114192) All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose. (114171, 114189.1, 114190, 114192.1, 114193, 114193.1, 114195, 114197, 114199, 114201, 114269) 2.00 All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Observed the hand wash sink nearest to the hot food holding unit was leaking. Repair/replace so there is no longer a leak when the water is turned on.

(REPEAT VIOLATION) Observed the three compartment sink near the deep fryer with the measured max water temperature at 114.5F during the inspection. Repair so hot water is provided at 120F minimum.
0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
4-07-2021 An accurate easily readable metal probe thermometer suitable for measuring temperature of food shall be available to the food handler. A thermometer +/- 2°F shall be provided for each hot and cold holding unit of potentially hazardous foods and high temperature warewashing machines. (114157, 114159) 1.00 Have a thermometer accurate to within 2°F or 1°C in each hot and cold holding unit. Have a metal probe type thermometer readily available on premises (to all appropriate staff) that is calibrated in accordance with the manufacturer's specifications as necessary to ensure accuracy. Observed the lack of a valid/working thermometer in the hot food and deli display unit. Failure to have a readily visible thermometer affixed to the warmest part of the refrigeration unit. Provide a thermometer in all units that hold potentially hazardous food items. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
4-07-2021 Potentially hazardous foods shall be held at or below 41°/ 45°F or at or above 135°F. (113996, 113998, 114037, 114343(a)) 7.00 Hold potentially hazardous foods either at or above 135°F or at or below 41°F. Hold the following potentially hazardous foods at 45°F: raw shell eggs, unshucked live molluscan shellfish, pasteurized milk and pasteurized milk products in original, sealed containers. Potentially hazardous foods held for dispensing in a serving line or a salad bar (not in a display case) may be held at 45°F or less during periods not to exceed 12 hours in any 24-hour period. Discard all potentially hazardous food that has been out of an approved time and temperature range. Observed cut Watermelon and Honeydew that were prepackaged at the facility was measured at 50F - 55F during the inspection. Items were removed from sale during the inspection. Keep all potentially hazardous food items at 41F an under.

Observed various food temperatures were measured between 44F - 47F in the display fridge units holding raw chicken and other products. Food items were stacked above the fill line which may have contributed to the food items being out of temperature. Shelves were dropped and food items were moved to below the fill line. Keep all food items below the fill line.
0114 RETAIL MARKET 30,001+ SQFT
4-07-2021 Any food is misbranded if its labeling is false or misleading, if it is offered for sale under the name of another food, or if it is an imitation of another food for which a definition and standard of identity has been established by regulation. (114087, 114089, 114089.1(a, b), 114090, 114093.1, 114377) 1.00 Present all food in a way that does not mislead or misinform consumers. Food or color additives, colored overwraps, lights or other misleading artificial means shall not be used to misrepresent the true appearance, color, or quality of a food.

The label shall contain the following information:
(1) The common name of the food.
(2) A list of ingredients in descending order of predominance by weight.
(3) The weight, count, or volume.
(4) The name and place of business of the manufacturer, packer, or distributor.
Nutrition labeling may also be required, and must be included when it is available from the manufacturer.

Food facility's or manufacturer's dating information, such as date codes or "use by" statements on packaging may not be concealed or altered.
Observed some prepackaged items lacking a required label on them. These items include cut melons, and donuts. Provide a label on all prepackaged items that are packaged at the facility. See corrective text for proper label requirements. 0114 RETAIL MARKET 30,001+ SQFT