Return To Restaurant Listing | Return to Environmental Health Homepage

Facility: Bellevue Bowl
Address: 785 Bellevue Rd, Atwater, CA

The most recent inspection of this food facility resulted in a rating of
Good (Total Points: 6.00)
0-6  Points: Good
7-13 Points: Satisfactory
14+  Points: Unsatisfactory
Rating on date 11-16-2021: Good (Total Points: 6.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
11-16-2021 The potable water supply shall be protected with a backflow or back siphonage protection device, as required by applicable plumbing codes. (114192) All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose. (114171, 114189.1, 114190, 114192.1, 114193, 114193.1, 114195, 114197, 114199, 114201, 114269) 1.00 All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Observed the soda machine and ice machine drainline is connected directly. Provide an air gap by way of a funnel drain or other methods. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
11-16-2021 The walls / ceilings shall have durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair. (114065, 114067, 114069, 114175, 114143, 114257, 114259.2, 114266, 114268, 114268.1, 114271, 114272) 1.00 All food facilities shall be kept clean, fully operative, and in good repair. Floor surfaces in all areas in which food is prepared, packaged or stored, where any utensil is washed, where refuse or garbage is stored, where janitorial facilities are located, and in all restrooms and hand washing areas shall be smooth and of durable construction and made from non absorbent material that is easily cleanable.

Each permanent food facility shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. Food facilities that are not fully enclosed on all sides and that are in operation on January 1, 1985, shall not be required to meet the requirements of this section until the facility is remodeled or has a significant menu change or a change in its method of operation. Full enclosure is not required for dining areas and certain other areas when approved for outdoor food services.
Observed the flooring in the newly installed walk-in fridge is VCT tile. This will be conditionally approved. Once and if the tile/flooring becomes damaged and no longer smooth and easily cleanable, the flooring will have to be replaced. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
11-16-2021 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 1.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method.
Observed the dishwashing machine was lacking sanitizer of suffucient strength dispensing in the dishwashing machine. Adjust so it is at 50PPM. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
11-16-2021 A person proposing to build or remodel a food facility shall submit plans for approval before starting any new construction or remodeling of any facility for use as a retail food facility. (114380, 114381) 1.00 A person proposing to build or remodel a food facility shall submit complete, easily readable plans drawn to scale and specifications to the Division of Environmental Health and obtain approval prior to starting any project. Existing bar was moved to a new location in the front of house. Flooring will need to be changed from the VCT tile to an approved flooring. Existing floor sinks are raised and not flushed with the existing flooring. The floor drains will need to be boxed in and sealed to prevent vermin harborage. This must be done by 5/20/2022. 0123 BAR
11-16-2021 The walls / ceilings shall have durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair. (114065, 114067, 114069, 114175, 114143, 114257, 114259.2, 114266, 114268, 114268.1, 114271, 114272) 1.00 All food facilities shall be kept clean, fully operative, and in good repair. Floor surfaces in all areas in which food is prepared, packaged or stored, where any utensil is washed, where refuse or garbage is stored, where janitorial facilities are located, and in all restrooms and hand washing areas shall be smooth and of durable construction and made from non absorbent material that is easily cleanable.

Each permanent food facility shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. Food facilities that are not fully enclosed on all sides and that are in operation on January 1, 1985, shall not be required to meet the requirements of this section until the facility is remodeled or has a significant menu change or a change in its method of operation. Full enclosure is not required for dining areas and certain other areas when approved for outdoor food services.
Observed the flooring in the newly installed bar area is VCT tile. This will need to be replaced with an approved flooring. Approved coving will also need to be added in the bar area under the three compartment sink. This will need to be completed by 5/20/2022. 0123 BAR
11-16-2021 The potable water supply shall be protected with a backflow or back siphonage protection device, as required by applicable plumbing codes. (114192) All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose. (114171, 114189.1, 114190, 114192.1, 114193, 114193.1, 114195, 114197, 114199, 114201, 114269) 1.00 All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Observed the floor sinks in the bar area are elevated and not flushed with the ground. The floor sink will need to be boxed and the space in between will need to be sealed, so there is an easy transition and no crevices for vermin. This will need to be completed by 5/20/2022. 0123 BAR