Return To Restaurant Listing | Return to Environmental Health Homepage

Facility: Applegate Market
Address: 1044 N. Applegate Road, Atwater, CA

The most recent inspection of this food facility resulted in a rating of
Good (Total Points: 6.00)
0-6  Points: Good
7-13 Points: Satisfactory
14+  Points: Unsatisfactory
Rating on date 1-07-2019: Good (Total Points: 6.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
1-07-2019 No violations were noted during this inspection. 0.00 This food facility currently meets California Retail Food Code requirements, and is authorized by the Merced County Division of Environmental Health to be open for business. The permit is issued to the current business owner of record and is non-transferable. No violations noted during inspection. 0110 RETAIL MARKET<2000 SQ FT (HM3)
1-07-2019 The potable water supply shall be protected with a backflow or back siphonage protection device, as required by applicable plumbing codes. (114192) All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose. (114171, 114189.1, 114190, 114192.1, 114193, 114193.1, 114195, 114197, 114199, 114201, 114269) 4.00 All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. (REPEAT VIOLATION) Observed leak at the hand wash station in the back food prep area. Repair so there is no longer a leak. Hot water knee pushing device is leaking when used. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
1-07-2019 Any food is misbranded if its labeling is false or misleading, if it is offered for sale under the name of another food, or if it is an imitation of another food for which a definition and standard of identity has been established by regulation. (114087, 114089, 114089.1(a, b), 114090, 114093.1, 114377) 2.00 Present all food in a way that does not mislead or misinform consumers. Food or color additives, colored overwraps, lights or other misleading artificial means shall not be used to misrepresent the true appearance, color, or quality of a food.

The label shall contain the following information:
(1) The common name of the food.
(2) A list of ingredients in descending order of predominance by weight.
(3) The weight, count, or volume.
(4) The name and place of business of the manufacturer, packer, or distributor.
Nutrition labeling may also be required, and must be included when it is available from the manufacturer.

Food facility's or manufacturer's dating information, such as date codes or "use by" statements on packaging may not be concealed or altered.
Observed the lack of required labels on the prepackaged burritos that are cooked at the facility. Provide a label with facility name, address, and phone number as well as a list of ingredients. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
1-07-2019 No violations were noted during this inspection. 0.00 This food facility currently meets California Retail Food Code requirements, and is authorized by the Merced County Division of Environmental Health to be open for business. The permit is issued to the current business owner of record and is non-transferable. No violations noted during inspection. 0151 CALCODE WELL WATER ANALYSES REQUIRED


Rating on date 12-07-2018: Unsatisfactory - reinspection required (Total Points: 19.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
12-07-2018 All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182) 2.00 Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.

Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.

The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated.
Observed the cabinet at the hand wash sink is damaged and no longer smooth and easily cleanable. Repair or replace fixture so that it is smooth and easily cleanable. High gloss paint with multiple layers may work. 0110 RETAIL MARKET<2000 SQ FT (HM3)
12-07-2018 All nonfood contact surfaces of utensils and equipment shall be clean. (114115, 114130.4) 2.00 Clean nonfood contact surfaces of equipment at a frequency necessary to prevent accumulation of residue. Observed the build up of mold on the racks inside the walk-in fridge. Clean and increase frequency to prevent build up. Employee started cleaning racks during inspection.

Observed slight build up of debris inside the hot coco machine. Clean and increase cleaning to prevent build up.
0110 RETAIL MARKET<2000 SQ FT (HM3)
12-07-2018 Potentially hazardous foods shall be held at or below 41°/ 45°F or at or above 135°F. (113996, 113998, 114037, 114343(a)) 2.00 Hold potentially hazardous foods either at or above 135°F or at or below 41°F. Hold the following potentially hazardous foods at 45°F: raw shell eggs, unshucked live molluscan shellfish, pasteurized milk and pasteurized milk products in original, sealed containers. Potentially hazardous foods held for dispensing in a serving line or a salad bar (not in a display case) may be held at 45°F or less during periods not to exceed 12 hours in any 24-hour period. Discard all potentially hazardous food that has been out of an approved time and temperature range. Observed food items in the hot holding unit measured at 128F - 130F. All food items in that range were reheated to 165F and placed back inside the hot holding unit. Unit was not turned to proper setting causing the temperature to drop. Unit was adjusted during inspection. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
12-07-2018 Wiping cloths used to wipe service counters, scales or other surfaces that may come into contact with food shall be used only once unless kept in clean water with sanitizer. (114135, 11485, 114185.1, 11485.2, 114185.3) 2.00 Cloths used to wipe service counters, scales, and other surfaces that may directly or indirectly contact food shall be used only once until laundered or may be used repeatedly if held in a sanitizing solution, as described below. Cloths used with raw foods of animal origin shall be used only once until laundered or may be used repeatedly if kept in a separate container of sanitizing solution, as described below:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with the manufacturer's use directions.
Observed the lack of sanitizer solution to store wiping cloths when using multiple times. Provide a bucket of sanitizer solution at all times when preparing food items and using wiping cloths multiple times. Bucket of sanitizer solution was created during inspection. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
12-07-2018 An adequate, protected, pressurized, potable supply of hot water and cold water shall be provided at all times. (113953(c), 114099.2(b) 114101(a), 114189, 114192, 114192.1, 114195) 7.00 Provide hot and cold water under pressure through a mixing valve to each sink compartment. The water supply shall be from a water system approved by the health officer or the state department. An adequate, protected, pressurized, potable supply of hot water, at least 120°F, and cold water shall be provided.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees
Observed the hot water temperature measured at 106F. Hot water heater was adjusted during inspection. Hot water of at least 120F must be provided at all times for proper cleaning. Facility must discontinue food prep until water temperature reaches 120F. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
12-07-2018 The potable water supply shall be protected with a backflow or back siphonage protection device, as required by applicable plumbing codes. (114192) All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose. (114171, 114189.1, 114190, 114192.1, 114193, 114193.1, 114195, 114197, 114199, 114201, 114269) 2.00 All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Observed leak at the hand wash station in the back food prep area. Repair so there is no longer a leak. Hot water knee pushing device is leaking when used. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
12-07-2018 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 2.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method.
Observed that chlorine test strips were expired and no longer working properly. Provide new chlorine test strips to measure sanitizer solution. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
12-07-2018 No violations were noted during this inspection. 0.00 This food facility currently meets California Retail Food Code requirements, and is authorized by the Merced County Division of Environmental Health to be open for business. The permit is issued to the current business owner of record and is non-transferable. No violations noted during inspection. 0151 CALCODE WELL WATER ANALYSES REQUIRED


Rating on date 4-02-2018: Satisfactory (Total Points: 10.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
4-02-2018 No violations were noted during this inspection. 0.00 This food facility currently meets California Retail Food Code requirements, and is authorized by the Merced County Division of Environmental Health to be open for business. The permit is issued to the current business owner of record and is non-transferable. All other violations from the previous inspection in the RETAIL MARKET <2000 SQ FT area have been corrected. 0110 RETAIL MARKET<2000 SQ FT (HM3)
4-02-2018 The potable water supply shall be protected with a backflow or back siphonage protection device, as required by applicable plumbing codes. (114192) All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose. (114171, 114189.1, 114190, 114192.1, 114193, 114193.1, 114195, 114197, 114199, 114201, 114269) 2.00 All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. 1) Observed lack of one inch minimum air gap between the drain lines under the food prep area handwashing sink and the rim height of the floor sink at the beginning of the inspection. Repair or modify drain lines so that the distance between the lowest edge of the drain lines and the height of the floor sink rim allows for a minimum of a one inch air gap. Pipes immediately trimmed. Corrected during inspection.

(2) Observed screen cover on the casing vent still torn / was mostly missing, no longer provides effective protection at the beginning of the inspection. Replace the torn screen cover on the casing vent. Small piece of new screen material immediately installed on the casing vent. Corrected during inspection.
0151 CALCODE WELL WATER ANALYSES REQUIRED
4-02-2018 No violations were noted during this inspection. 0.00 This food facility currently meets California Retail Food Code requirements, and is authorized by the Merced County Division of Environmental Health to be open for business. The permit is issued to the current business owner of record and is non-transferable. All other violations from the previous inspection in the CALCODE WELL WATER ANALYSES REQUIRED area have been corrected. 0151 CALCODE WELL WATER ANALYSES REQUIRED
4-02-2018 All food employees shall have adequate knowledge of and be trained in food safety as it relates to their assigned duties. The person in charge shall have adequate knowledge of, and shall educate employees of the food facility regarding major food allergens. (113947) Food facilities that prepare, handle or serve non-prepackaged potentially hazardous food, shall have an employee who has passed an approved food safety certification examination. (113947-113947.1) 0.00 The responsibilities of the staff member certified in food safety include ensuring that all employees who handle, or have responsibility for handling, unpackaged foods of any kind have sufficient knowledge to ensure the safe preparation and /or service of the food. The nature and extent of the knowledge that each employee is required to have may be tailored, as appropriate, to the employee's duties related to food safety issues. REMINDER to provide a copy of the unexpired Food Managers Certificate to MCDEH by no later than 4/30/18. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
4-02-2018 An adequate, protected, pressurized, potable supply of hot water and cold water shall be provided at all times. (113953(c), 114099.2(b) 114101(a), 114189, 114192, 114192.1, 114195) 4.00 Provide hot and cold water under pressure through a mixing valve to each sink compartment. The water supply shall be from a water system approved by the health officer or the state department. An adequate, protected, pressurized, potable supply of hot water, at least 120°F, and cold water shall be provided.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees
REPEAT: Observed the water temperature at the three compartment sink reached a maximum of 64ºF at the beginning of the inspection. Per the owner, repairman working on cardboard baler had turned off circuit breakers earlier and staff had not realized it had not been turned back on to the hot water heater yet. Adjust or repair so as to provide water at not less than 120ºF. Hot water heater breaker turned back on. Periodically recheck of hot water temperatures showing a steady rise in temperature. Hot water heater reading of 117ºF obtained by 3:30 PM. Continue to monitor / adjust / repair as needed to ensure hot water to the three compartment sink is consistently capable of reaching a minimum of 120ºF for the required wash / rinse / sanitize process for all utensils, dishes, and food contact surfaces. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
4-02-2018 No violations were noted during this inspection. 0.00 This food facility currently meets California Retail Food Code requirements, and is authorized by the Merced County Division of Environmental Health to be open for business. The permit is issued to the current business owner of record and is non-transferable. All other violations from the previous inspection in the FOOD ESTAB. W/FOOD PREP 0-49 SEATS area have been corrected. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
4-02-2018 All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182) 4.00 Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.

Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.

The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated.
REPEAT: Observed edges of cupboards below area where rotisserie / box fryer / deli meat slicer are located, are still damaged or missing finished edges allowing the inner compressed composite material to be exposed. Cabinet below the handwashing sink near the soda fountains is also in a similar condition. Repair or replace the damaged edging / finishes on all the damaged cupboard doors and edges such that all surfaces in the food prep / sink areas are smooth, easily cleanable, non porous, and meet a commercial grade standard. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)


Rating on date 2-28-2018: Unsatisfactory - reinspection required (Total Points: 18.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
2-28-2018 Handwashing signs shall be posted in each toilet room, directing attention to the need to thoroughly wash hands after using the restroom. (113953.5)

No smoking signs shall be posted in food preparation, food storage, and warewashing areas. (113978)

Consumers shall be notified that clean tableware is to be used when they return to self-service areas such as salad bars and buffets. (114075)

Any food facility constructed before January 1, 2004 without public toilet facilities shall prominently post a sign within the food facility in a public area stating that toilet facilities are not provided. (113725.1, 114276, 114381 (e))
2.00 Post permit in a conspicuous place (It is recommended that the permit be in customer view.). Post a notice advising patrons that a copy of the most recent routine inspection report is available for review by interested parties. Keep a copy of the most recent health inspection report at the facility for customer review purposes.

Post and maintain a legible and conspicuous sign in each toilet room directing attention to the need to thoroughly wash hands after using the toilet.

Post and maintain a legible "No Smoking" sign in food preparation, food storage, and utensil washing areas.

(1) Observed lack of the required handwashing sign in the restroom. Sign drawn up and posted immediately. Corrected during inspection.

(2) Observed lack of the required "do not drink the tap water" signs at the sinks throughout the facility. Signs drawn up and posted immediately at all sinks. Corrected during inspection.

NOTE: To continue your exemption from the state water system permitting requirements, please ensure the CalCode Exemption Annual Verification form for 2018 is reviewed, signed, and returned to MCDEH within 30 days.
0151 CALCODE WELL WATER ANALYSES REQUIRED
2-28-2018 The potable water supply shall be protected with a backflow or back siphonage protection device, as required by applicable plumbing codes. (114192) All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose. (114171, 114189.1, 114190, 114192.1, 114193, 114193.1, 114195, 114197, 114199, 114201, 114269) 2.00 All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. (1) Observed lack of one inch minimum air gap between the drain lines under the food prep area handwashing sink and the rim height of the floor sink. Repair or modify drain lines so that the distance between the lowest edge of the drain lines and the height of the floor sink rim allows for a minimum of a one inch air gap.

(2) Observed screen cover on the casing vent has torn / is mostly missing, no longer provides effective protection. Replace the torn screen cover on the casing vent.
0151 CALCODE WELL WATER ANALYSES REQUIRED
2-28-2018 An adequate, protected, pressurized, potable supply of hot water and cold water shall be provided at all times. (113953(c), 114099.2(b) 114101(a), 114189, 114192, 114192.1, 114195) 2.00 Provide hot and cold water under pressure through a mixing valve to each sink compartment. The water supply shall be from a water system approved by the health officer or the state department. An adequate, protected, pressurized, potable supply of hot water, at least 120°F, and cold water shall be provided.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees
Observed the water temperature at the three compartment sink reaches a maximum of 115ºF. Adjust or repair so as to provide water at not less than 120ºF. Provide hot and cold water under pressure through a mixing valve to each sink compartment. Hot water shall be at least 120ºF. Warm tempered water (100-108ºF) may be substituted for hot and cold water at handwashing sinks. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
2-28-2018 All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182) 2.00 Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.

Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.

The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated.
(1) Observed edges of cupboards below area where rotisserie / box fryer / deli meat slicer are located, have damaged or missing finished edges allowing the inner compressed composite material to be exposed. Repair or replace the damaged edging / finishes on the cupboard doors and edges such that all surfaces in the food prep area are smooth, easily cleanable, non porous, and meet a commercial grade standard.

(2) Per conversation with staff, minor temperature variation (41-44ºF) in items in deli style display cooler is due to the unit's large doors and frequent opening of this unit during morning food prepping, and when the unit is adjusted colder, it tends to "freeze up" in the afternoons when it is opened less. Have this unit serviced, repaired, or replaced such that appropriate cold holding temperatures (not more than 41ºF) are maintained for the type of items being held in this location consistently throughout the day.
0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
2-28-2018 All food employees shall have adequate knowledge of and be trained in food safety as it relates to their assigned duties. The person in charge shall have adequate knowledge of, and shall educate employees of the food facility regarding major food allergens. (113947) Food facilities that prepare, handle or serve non-prepackaged potentially hazardous food, shall have an employee who has passed an approved food safety certification examination. (113947-113947.1) 2.00 The responsibilities of the staff member certified in food safety include ensuring that all employees who handle, or have responsibility for handling, unpackaged foods of any kind have sufficient knowledge to ensure the safe preparation and /or service of the food. The nature and extent of the knowledge that each employee is required to have may be tailored, as appropriate, to the employee's duties related to food safety issues. Observed lack of proof that a current employee of this establishment holds a Food Safety Manager Class certificate that is no more than five years old (manager certificate on site is expired). Maintain a copy of the original certificate for at least one current employee at the facility location. The food managers certificate that is earned by the employee or owner may be used at only one location. Obtain a certificate from an American National Standards Institute approved food handling/food safety examination; if no one holds a current food safety certificate, obtain one within 60 days. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
2-28-2018 An accurate easily readable metal probe thermometer suitable for measuring temperature of food shall be available to the food handler. A thermometer +/- 2°F shall be provided for each hot and cold holding unit of potentially hazardous foods and high temperature warewashing machines. (114157, 114159) 2.00 Have a thermometer accurate to within 2°F or 1°C in each hot and cold holding unit. Have a metal probe type thermometer readily available on premises (to all appropriate staff) that is calibrated in accordance with the manufacturer's specifications as necessary to ensure accuracy. Observed lack of any probe thermometers at this facility location. Obtain and use probe thermometers to ensure PHF (Potentially Hazardous Food) items are being cooked to or cooled to and held at the correct required temperatures (41ºF or below, or 135ºF or above), and to verify that water temperatures at the sinks are at the correct range at each sink location (not less than 100ºF at all handwashing sinks, and not less than 120ºF at all other sinks). Failure to provide approved probe thermometers. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
2-28-2018 Failure to keep food pure and free from contamination, adulteration and spoilage. Any food is adulterated if it bears or contains any poisonous or deleterious substance that may render it impure or injurious to health. (113967, 113976, 113980, 113988, 113990, 114035, 114254(c), 114254.3) 2.00 Provide adequate protection at all times to keep food pure and free from contamination, adulteration and spoilage. Destroy all contaminated, adulterated and spoiled food. Observed six cans of powdered formula of the same type with a day of 01 DEC 17 embossed in the bottom of the cans. Cans immediately removed from the sales area. Corrected during inspection.

(a) A retail food facility shall not sell of offer for sale after the "use by" date, infant formula or baby food that is required to have this date on its packaging pursuant to the federal act, as defined in Section 109930, and federal regulations adopted pursuant to the federal act, including, but not limited to, Section 107.20 of Title 21 of the Code of Federal Regulations.
(b) Notwithstanding Section 114395, any retail food facility that violates this section is guilty of an infraction, punishable by a fine of not more than ten dollars ($10) per day for each item sold or offered for sale after the "use by" date. The fine shall be calculated based upon the number of days past the "use by" date that the product is either found being offered for sale, or if the product is sold, the date of sale as established by evidence of the proof of purchase, including, but not limited to, a sales receipt.
(c) An enforcement agency may assess administrative penalties on a retail food facility that violates this section in the amount of ten dollars ($10) per day for each item sold or offered for sale, in addition to other penalties authorized by law.
(d) For purposes of this section, the following definitions shall apply:
(1) "Baby food" shall have the meaning given to "baby foods" in paragraph (c) of Section 407.81 of Title 40 of the Code of Federal Regulations.
(2) "Infant formula" shall have the meaning given in subdivision (z) of Section 321 of Title 21 of the United States Code.
0110 RETAIL MARKET<2000 SQ FT (HM3)
2-28-2018 All nonfood contact surfaces of utensils and equipment shall be clean. (114115, 114130.4) 2.00 Clean nonfood contact surfaces of equipment at a frequency necessary to prevent accumulation of residue. (1) Observed build up of dust debris on fan blade guards on cooler unit in walk-in refrigerator and/or freezer. Improve cleaning frequency so as to prevent a visible buildup of dust debris.

(2) Observed accumulation of plastic, cardboard, and other miscellaneous debris in the walk in cooler, especially below the display racking. Improve cleaning frequency to prevent the accumulation of debris.
0110 RETAIL MARKET<2000 SQ FT (HM3)
2-28-2018 Exhaust hoods shall be provided to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6" beyond all cooking equipment. All areas shall have sufficient ventilation to facilitate proper food storage. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. (114149, 114149.1) Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields. (114149.2, 114149.3, 114252, 114252.1) 2.00 All areas shall have sufficient ventilation to facilitate proper food storage and to provide a reasonable condition of comfort for each employee, consistent with the job performed by the employee.

Light fixtures in areas where food is prepared, open food is stored, or utensils are cleaned shall be of shatterproof construction or shall be protected with shatterproof shields and shall be readily cleanable. In every room and area in which any food is prepared, manufactured, processed, or prepackaged, or in which equipment or utensils are cleaned, sufficient natural or artificial lighting shall be provided to produce the following light intensity, while the area is in use:
(a) At least 10-foot candles for the following:
(1) At a distance of 30 inches above the floor, in walk-in refrigeration units, and dry food storage areas.
(2) At a working surface on which alcoholic beverages are prepared or where utensils used in the preparation or service of alcoholic beverages are cleaned.
(3) Inside equipment, such as reach-in or under-the-counter refrigerators.
(b) At least 20-foot candles for the following:
(1) At a surface where food is provided for consumer self-service or where fresh produce or prepackaged foods are sold or offered for consumption.
(2) In server stations where food is prepared.
(3) At a distance of 30 inches above the floor in areas used for handwashing, warewashing, and equipment and utensil storage, and in toilet rooms.
(c) Except in server stations where food is prepared, at least 50-foot candles at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor.
Observed the center light fixture in / over the walk in cooler does not function, bulb may be burned out. Replace bulb and / or repair fixture. Failure to provide adequate lighting. 0110 RETAIL MARKET<2000 SQ FT (HM3)