Return To Restaurant Listing | Return to Environmental Health Homepage

Facility: Henry Miller School
Address: 545 W. L St., Los Banos, CA

The most recent inspection of this food facility resulted in a rating of
Good (Total Points: 4.00)
0-6  Points: Good
7-13 Points: Satisfactory
14+  Points: Unsatisfactory
Rating on date 4-05-2024: Good (Total Points: 4.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
4-05-2024 All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182) 1.00 Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.

Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.

The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated.
1. Observed single Door Beverage Air refrigerator was down for repair since 3/1 All equipment shall be in maintained and in good condition. Repair or remove from facility
2. Observed that dish machine was out of order. Confirm if this item will be repaired with MCDEH. If not keep item maintained and in good condition or remove.
3. Observed Out of order microwave near service counter. All equipment shall be in maintained and in good condition. Repair or remove from facility
4. Observed that the grandfathered freezer had a large amount of ice that had accumulated on to the stored food. De Ice refrigrator to prevent damage and protect prepackaged food. All equipment shall be in maintained and in good condition.
0122 CAFETERIA [SCHOOL]
4-05-2024 An adequate, protected, pressurized, potable supply of hot water and cold water shall be provided at all times. (113953(c), 114099.2(b) 114101(a), 114189, 114192, 114192.1, 114195) 3.00 Provide hot and cold water under pressure through a mixing valve to each sink compartment. The water supply shall be from a water system approved by the health officer or the state department. An adequate, protected, pressurized, potable supply of hot water, at least 120°F, and cold water shall be provided.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees
1. Observed student restrooms were connected to an instantaneous hot water heater however it was not functioning. Repair so both student restrooms have hot water of 100-108F 0122 CAFETERIA [SCHOOL]


Rating on date 3-06-2023: Good (Total Points: 0.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
3-06-2023 No violations were noted during this inspection. 0.00 This food facility currently meets California Retail Food Code requirements, and is authorized by the Merced County Division of Environmental Health to be open for business. The permit is issued to the current business owner of record and is non-transferable. no violations observed 0122 CAFETERIA [SCHOOL]


Rating on date 5-31-2022: Good (Total Points: 6.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
5-31-2022 The walls / ceilings shall have durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair. (114065, 114067, 114069, 114175, 114143, 114257, 114259.2, 114266, 114268, 114268.1, 114271, 114272) 2.00 All food facilities shall be kept clean, fully operative, and in good repair. Floor surfaces in all areas in which food is prepared, packaged or stored, where any utensil is washed, where refuse or garbage is stored, where janitorial facilities are located, and in all restrooms and hand washing areas shall be smooth and of durable construction and made from non absorbent material that is easily cleanable.

Each permanent food facility shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. Food facilities that are not fully enclosed on all sides and that are in operation on January 1, 1985, shall not be required to meet the requirements of this section until the facility is remodeled or has a significant menu change or a change in its method of operation. Full enclosure is not required for dining areas and certain other areas when approved for outdoor food services.
(REPEAT VIOLATION) MOP SINK ROOM: Wall paint has peeled off next to the FRP panel. Repair to provide smooth, easily cleanable, and non-absorbent surfaces. 0122 CAFETERIA [SCHOOL]
5-31-2022 Handwashing soap and single use towels or drying device shall be provided in dispensers adjacent to each handwashing facility; dispensers shall be maintained in good repair. (113953.2) Adequate separate facilities shall be provided for handwashing, food preparation, and the washing of utensils and equipment. (113953, 113953.1) 3.00 Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees. Employees shall not clean their hands in a sink used for food preparation, warewashing, or in a service sink or a curbed cleaning facility used for the disposal of mop water and similar liquid waste. Do not place objects in front of the handwashing station, and do not place items, utensils or wiping cloths in the handwashing sink.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Soap shall be provided in approved dispensers at, or adjacent to, handwashing facilities (no bars of soap). Single-use sanitary towels or hot-air blowers shall be provided at handwashing facilities in approved dispensing devices.
Observed the temperature of the water at the premixed hand wash sink for the restroom was measured at 79F. Adjust so it is between 100F - 108F for proper hand washing. 0122 CAFETERIA [SCHOOL]
5-31-2022 Exhaust hoods shall be provided to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6" beyond all cooking equipment. All areas shall have sufficient ventilation to facilitate proper food storage. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. (114149, 114149.1) Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields. (114149.2, 114149.3, 114252, 114252.1) 1.00 All areas shall have sufficient ventilation to facilitate proper food storage and to provide a reasonable condition of comfort for each employee, consistent with the job performed by the employee.

Light fixtures in areas where food is prepared, open food is stored, or utensils are cleaned shall be of shatterproof construction or shall be protected with shatterproof shields and shall be readily cleanable. In every room and area in which any food is prepared, manufactured, processed, or prepackaged, or in which equipment or utensils are cleaned, sufficient natural or artificial lighting shall be provided to produce the following light intensity, while the area is in use:
(a) At least 10-foot candles for the following:
(1) At a distance of 30 inches above the floor, in walk-in refrigeration units, and dry food storage areas.
(2) At a working surface on which alcoholic beverages are prepared or where utensils used in the preparation or service of alcoholic beverages are cleaned.
(3) Inside equipment, such as reach-in or under-the-counter refrigerators.
(b) At least 20-foot candles for the following:
(1) At a surface where food is provided for consumer self-service or where fresh produce or prepackaged foods are sold or offered for consumption.
(2) In server stations where food is prepared.
(3) At a distance of 30 inches above the floor in areas used for handwashing, warewashing, and equipment and utensil storage, and in toilet rooms.
(c) Except in server stations where food is prepared, at least 50-foot candles at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor.
Observed the fan unit in girls restroom in the cafeteria was not functional. Toilet rooms shall be vented to the outside air by means of an openable, screened window, an air shaft, or a light-switch-activated exhaust fan, consistent with the requirements of local building codes. Repair or replace so it is functional. 0122 CAFETERIA [SCHOOL]


Rating on date 4-13-2021: Good (Total Points: 3.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
4-13-2021 The walls / ceilings shall have durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair. (114065, 114067, 114069, 114175, 114143, 114257, 114259.2, 114266, 114268, 114268.1, 114271, 114272) 1.00 All food facilities shall be kept clean, fully operative, and in good repair. Floor surfaces in all areas in which food is prepared, packaged or stored, where any utensil is washed, where refuse or garbage is stored, where janitorial facilities are located, and in all restrooms and hand washing areas shall be smooth and of durable construction and made from non absorbent material that is easily cleanable.

Each permanent food facility shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. Food facilities that are not fully enclosed on all sides and that are in operation on January 1, 1985, shall not be required to meet the requirements of this section until the facility is remodeled or has a significant menu change or a change in its method of operation. Full enclosure is not required for dining areas and certain other areas when approved for outdoor food services.
MOP SINK ROOM: Wall paint has peeled off next to the FRP panel. Repair to provide smooth, easily cleanable, and non-absorbent surfaces. 0122 CAFETERIA [SCHOOL]
4-13-2021 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 1.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method.
AUTOMATIC DISHWASHER: This unit uses a chlorine sanitizer so provide sanitizer testing strips for measuring the sanitizer concentration. (The 2-compartment dishwashing sink had quaternary ammonium testing strips for quaternary ammonium tablets near the sink). 0122 CAFETERIA [SCHOOL]
4-13-2021 All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182) 1.00 Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.

Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.

The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated.
1) MILK REFRIGERATOR BOXES: The protective paint has peeled off some shelves causing the metal to be exposed and rusted in some areas. Repair or replace.

2) 1-DOOR TALL REFRIGERATOR NEAR THE MOP SINK ROOM: The protective paint has peeled off some shelves causing the metal to be exposed and rusted in some areas. Repair or replace.
0122 CAFETERIA [SCHOOL]