Return To Restaurant Listing | Return to Environmental Health Homepage

Facility: Circle K Store #2705017
Address: 2549 Blossom St., Dos Palos, CA

The most recent inspection of this food facility resulted in a rating of
Good (Total Points: 0.00)
0-6  Points: Good
7-13 Points: Satisfactory
14+  Points: Unsatisfactory
Rating on date 3-01-2019: Good (Total Points: 0.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
3-01-2019 No violations were noted during this inspection. 0.00 This food facility currently meets California Retail Food Code requirements, and is authorized by the Merced County Division of Environmental Health to be open for business. The permit is issued to the current business owner of record and is non-transferable. All previous violations have been corrected. 0111 RETAIL MARKET 2001-6000 SQFT


Rating on date 2-14-2019: Unsatisfactory - reinspection required (Total Points: 20.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
2-14-2019 The walls / ceilings shall have durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair. (114065, 114067, 114069, 114175, 114143, 114257, 114259.2, 114266, 114268, 114268.1, 114271, 114272) 4.00 All food facilities shall be kept clean, fully operative, and in good repair. Floor surfaces in all areas in which food is prepared, packaged or stored, where any utensil is washed, where refuse or garbage is stored, where janitorial facilities are located, and in all restrooms and hand washing areas shall be smooth and of durable construction and made from non absorbent material that is easily cleanable.

Each permanent food facility shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. Food facilities that are not fully enclosed on all sides and that are in operation on January 1, 1985, shall not be required to meet the requirements of this section until the facility is remodeled or has a significant menu change or a change in its method of operation. Full enclosure is not required for dining areas and certain other areas when approved for outdoor food services.
1) FLOOR UNDERNEATH THE COFFEE STATION: Debris (lids, straws, dirt) and sticky residue accumulation. Clean. REPEAT VIOLATION

2) FLOOR UNDERNEATH THE SODA FOUNTAINS: Debris (lids, straws, dirt) and sticky residue accumulation. Clean. REPEAT VIOLATION

3) FLOOR UNDERNEATH THE FROSTER MACHINES: Debris (lids, straws, dirt) and sticky residue accumulation. Clean. REPEAT VIOLATION

4) FLOOR UNDERNEATH THE HOTDOG ISLAND: Dirt/dust accumulation. Clean. REPEAT VIOLATION

5) INSIDE THE CABINETS STORING MINI TRASH CANS: Sticky residue and debris accumulation. Clean. REPEAT VIOLATION

6) FLOOR UNDERNEATH THE SODA BIB RACK: Plastic cap accumulation. Clean. REPEAT VIOLATION
0111 RETAIL MARKET 2001-6000 SQFT
2-14-2019 The potable water supply shall be protected with a backflow or back siphonage protection device, as required by applicable plumbing codes. (114192) All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose. (114171, 114189.1, 114190, 114192.1, 114193, 114193.1, 114195, 114197, 114199, 114201, 114269) 4.00 All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. 1) MOP SINK: When the water is turned on, water is leaking heavily from the center vacuum breaker. The problem is worse than the last few years. There is more water leaking than there is water coming out of the faucet. The hot water handle is also stripped and constantly turns. Replace the faucet. REPEAT VIOLATION FROM THE PAST INSPECTIONS

2) FLOOR SINK/DRAIN NEAR THE CUSTOMER SODA MACHINES: Brown slime/residue accumulation inside the floor sink. Clean. REPEAT VIOLATION
0111 RETAIL MARKET 2001-6000 SQFT
2-14-2019 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 4.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method.
1) 3-COMPARTMENT SINK: Replace the (2) missing sink drain plugs so as to be able to properly wash, rinse, and sanitize dishes. REPEAT VIOLATION

2) 3-COMPARTMENT SINK: Facility ran out of the usual quaternary ammonium sanitizer and was using bleach as the alternative sanitizer. Chlorine sanitizer testing strips were available but the manufacturer's label on the strip container stated the strips expired in January 2007. Replace the expired strips. Provide quaternary sanitizer testing strips if you plan to continue using quaternary ammonium sanitizer in the future. REPEAT VIOLATION
0111 RETAIL MARKET 2001-6000 SQFT
2-14-2019 All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182) 4.00 Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.

Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.

The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated.
1) BEER/WATER WALK-IN REFRIGERATOR: Mold accumulation on the black shelves. Clean. REPEAT VIOLATION

2) 2-DOOR TRUE FREEZER NEAR THE MANAGER'S OFFICE: Heavy ice accumulation on the exterior space between the two doors. Ice accumulation on the black gaskets around both doors. Clean and Repair. REPEAT VIOLATION

3) SODA WALK-IN REFRIGERATOR: A functional light bulb was provided inside the light fixture. There is still water accumulation inside the globe. REPEAT VIOLATION

4) 1-DOOR SILVER KELVINATOR REFRIGERATOR NEXT TO THE MOP SINK: Rusty bottom shelf. Repair or replace to provide smooth, easily cleanable, and non-absorbent surfaces. REPEAT VIOLATION
0111 RETAIL MARKET 2001-6000 SQFT
2-14-2019 Toilet facilities shall be maintained clean, sanitary and in good repair. Toilet rooms shall be separated by a well-fitting self-closing door. Toilet tissue shall be provided in a permanently installed dispenser at each toilet. The number of toilet facilities shall be in accordance with local building and plumbing ordinances. Toilet facilities shall be provided for patrons: in establishments with more than 20,000 sq ft.; establishments offering on-site food consumption. (113953, 113953.1, 113953.2, 114250, 114250.1, 114276) 4.00 Provide clean toilet facilities in good repair. Provide permanently installed toilet tissue dispenser(s) in all toilet facilities. Provide handwashing facilities within or adjacent to all toilet facilities. Soap shall be provided in dispensers at, or adjacent to, handwashing facilities. Single-use sanitary towels in dispensers or hot-air blowers shall be provided at handwashing facilities.

Customer restrooms are required for food facilities of more than 20,000 square feet if they were constructed after July 1 1984, and also applies to facilities of any size that were constructed after January 1, 2004 where there is onsite consumption of food. A "take-out only" food facility, with no seating indoors or outdoors, may not be required to provide customer restrooms. Check with the Division of Environmental Health and with the appropriate Planning Department before removing or restricting access to customer restrooms.
CUSTOMER/EMPLOYEE RESTROOM: Toilet paper rolls were sitting on the toilet tank cover. Provide the correct toilet paper inside the existing dispenser or replace the dispenser to fit the existing toilet paper rolls. REPEAT VIOLATION 0111 RETAIL MARKET 2001-6000 SQFT


Rating on date 1-02-2019: Unsatisfactory - reinspection required (Total Points: 16.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
1-02-2019 The potable water supply shall be protected with a backflow or back siphonage protection device, as required by applicable plumbing codes. (114192) All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose. (114171, 114189.1, 114190, 114192.1, 114193, 114193.1, 114195, 114197, 114199, 114201, 114269) 4.00 All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. 1) MOP SINK: When the water is turned on, water is leaking heavily from the center vacuum breaker. The problem is worse than the last few years. There is more water leaking than there is water coming out of the faucet. The hot water handle is also stripped and constantly turns. Replace the faucet. REPEAT VIOLATION FROM THE PAST INSPECTIONS

2) FLOOR SINK/DRAIN NEAR THE CUSTOMER SODA MACHINES: Brown slime/residue accumulation inside the floor sink. Clean.
0111 RETAIL MARKET 2001-6000 SQFT
1-02-2019 All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182) 2.00 Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.

Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.

The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated.
1) BEER/WATER WALK-IN REFRIGERATOR: Mold accumulation on the black shelves. Clean.

2) 1-DOOR SILVER KELVINATOR FREEZER NEAR THE MANAGER'S OFFICE: Dirt accumulation on the bottom shelf. Clean.

3) 2-DOOR TRUE FREEZER NEAR THE MANAGER'S OFFICE: Heavy ice accumulation on the exterior space between the two doors. Ice accumulation on the black gaskets around both doors. Clean and Repair.
0111 RETAIL MARKET 2001-6000 SQFT
1-02-2019 Toilet facilities shall be maintained clean, sanitary and in good repair. Toilet rooms shall be separated by a well-fitting self-closing door. Toilet tissue shall be provided in a permanently installed dispenser at each toilet. The number of toilet facilities shall be in accordance with local building and plumbing ordinances. Toilet facilities shall be provided for patrons: in establishments with more than 20,000 sq ft.; establishments offering on-site food consumption. (113953, 113953.1, 113953.2, 114250, 114250.1, 114276) 2.00 Provide clean toilet facilities in good repair. Provide permanently installed toilet tissue dispenser(s) in all toilet facilities. Provide handwashing facilities within or adjacent to all toilet facilities. Soap shall be provided in dispensers at, or adjacent to, handwashing facilities. Single-use sanitary towels in dispensers or hot-air blowers shall be provided at handwashing facilities.

Customer restrooms are required for food facilities of more than 20,000 square feet if they were constructed after July 1 1984, and also applies to facilities of any size that were constructed after January 1, 2004 where there is onsite consumption of food. A "take-out only" food facility, with no seating indoors or outdoors, may not be required to provide customer restrooms. Check with the Division of Environmental Health and with the appropriate Planning Department before removing or restricting access to customer restrooms.
CUSTOMER/EMPLOYEE RESTROOM: Toilet paper rolls were sitting on the toilet tank cover and on the handicap grab rails. Provide the correct toilet paper inside the existing dispenser or replace the dispenser to fit the existing toilet paper rolls. 0111 RETAIL MARKET 2001-6000 SQFT
1-02-2019 Exhaust hoods shall be provided to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6" beyond all cooking equipment. All areas shall have sufficient ventilation to facilitate proper food storage. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. (114149, 114149.1) Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields. (114149.2, 114149.3, 114252, 114252.1) 2.00 All areas shall have sufficient ventilation to facilitate proper food storage and to provide a reasonable condition of comfort for each employee, consistent with the job performed by the employee.

Light fixtures in areas where food is prepared, open food is stored, or utensils are cleaned shall be of shatterproof construction or shall be protected with shatterproof shields and shall be readily cleanable. In every room and area in which any food is prepared, manufactured, processed, or prepackaged, or in which equipment or utensils are cleaned, sufficient natural or artificial lighting shall be provided to produce the following light intensity, while the area is in use:
(a) At least 10-foot candles for the following:
(1) At a distance of 30 inches above the floor, in walk-in refrigeration units, and dry food storage areas.
(2) At a working surface on which alcoholic beverages are prepared or where utensils used in the preparation or service of alcoholic beverages are cleaned.
(3) Inside equipment, such as reach-in or under-the-counter refrigerators.
(b) At least 20-foot candles for the following:
(1) At a surface where food is provided for consumer self-service or where fresh produce or prepackaged foods are sold or offered for consumption.
(2) In server stations where food is prepared.
(3) At a distance of 30 inches above the floor in areas used for handwashing, warewashing, and equipment and utensil storage, and in toilet rooms.
(c) Except in server stations where food is prepared, at least 50-foot candles at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor.
1) SODA WALK-IN REFRIGERATOR: One light fixture near the fans was missing a light bulb and had water inside the clear globe. Replace the missing light bulb and repair the fixture.

2) 1-DOOR SILVER KELVINATOR REFRIGERATOR NEXT TO THE MOP SINK: Rusty bottom shelf. Rusty white shelves. Repair or replace to provide smooth, easily cleanable, and nonabsorbent surfaces.
0111 RETAIL MARKET 2001-6000 SQFT
1-02-2019 Additional information provided to facility operators 0.00 Excerpts from California Health and Safety Code, Division 104 (Environmental Health), Part 7 (California Retail Food Code), sections 113700 through 114437. PAPER TOWEL DISPENSERS AT THE DISHWASHING SINK AND HANDWASHING SINK: Dispensers were empty during inspection. Employee was notified and refilled the dispensers during the inspection. Keep dispensers filled at all times during operational hours as open food handling (putting food on the hot rollers) occurs throughout the day. 0111 RETAIL MARKET 2001-6000 SQFT
1-02-2019 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 2.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method.
1) 3-COMPARTMENT SINK: Replace the (2) missing sink drain plugs so as to be able to properly wash, rinse, and sanitize dishes.

2) 3-COMPARTMENT SINK: Facility ran out of the usual quaternary ammonium sanitizer and was using bleach as the alternative sanitizer. Chlorine sanitizer testing strips were available but the manufacturer's label on the strip container stated the strips expired in January 2007. Replace the expired strips. Provide quaternary sanitizer testing strips if you plan to continue using quaternary ammonium sanitizer in the future.
0111 RETAIL MARKET 2001-6000 SQFT
1-02-2019 The walls / ceilings shall have durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair. (114065, 114067, 114069, 114175, 114143, 114257, 114259.2, 114266, 114268, 114268.1, 114271, 114272) 4.00 All food facilities shall be kept clean, fully operative, and in good repair. Floor surfaces in all areas in which food is prepared, packaged or stored, where any utensil is washed, where refuse or garbage is stored, where janitorial facilities are located, and in all restrooms and hand washing areas shall be smooth and of durable construction and made from non absorbent material that is easily cleanable.

Each permanent food facility shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. Food facilities that are not fully enclosed on all sides and that are in operation on January 1, 1985, shall not be required to meet the requirements of this section until the facility is remodeled or has a significant menu change or a change in its method of operation. Full enclosure is not required for dining areas and certain other areas when approved for outdoor food services.
1) FLOOR UNDERNEATH THE COFFEE STATION: Debris (lids, straws, dirt) and sticky residue accumulation. Clean. REPEAT VIOLATION

2) FLOOR UNDERNEATH THE SODA FOUNTAINS: Debris (lids, straws, dirt) and sticky residue accumulation. Clean. REPEAT VIOLATION

3) FLOOR UNDERNEATH THE FROSTER MACHINES: Debris (lids, straws, dirt) and sticky residue accumulation. Clean. REPEAT VIOLATION

4) FLOOR UNDERNEATH THE HOTDOG ISLAND: Dirt/dust accumulation. Clean. REPEAT VIOLATION

5) INSIDE THE CABINETS STORING MINI TRASH CANS: Sticky residue and debris accumulation. Clean. REPEAT VIOLATION

6) FLOOR UNDERNEATH THE SODA BIB RACK: Plastic cap and sticky residue accumulation. Clean. REPEAT VIOLATION
0111 RETAIL MARKET 2001-6000 SQFT