Return To Restaurant Listing | Return to Environmental Health Homepage

Facility: Taco Grotto
Address: 1420 Elgin Ave, Dos Palos, CA

The most recent inspection of this food facility resulted in a rating of
Satisfactory (Total Points: 13.00)
0-6  Points: Good
7-13 Points: Satisfactory
14+  Points: Unsatisfactory
Rating on date 9-09-2021: Satisfactory (Total Points: 13.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
9-09-2021 An accurate easily readable metal probe thermometer suitable for measuring temperature of food shall be available to the food handler. A thermometer +/- 2°F shall be provided for each hot and cold holding unit of potentially hazardous foods and high temperature warewashing machines. (114157, 114159) 1.00 Have a thermometer accurate to within 2°F or 1°C in each hot and cold holding unit. Have a metal probe type thermometer readily available on premises (to all appropriate staff) that is calibrated in accordance with the manufacturer's specifications as necessary to ensure accuracy. Observed the lack of a valid probe thermometer at the facility. Provide a valid probe thermometer for proper food temperature measurement. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
9-09-2021 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 1.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method. 		(CDI) Observed the sanitizer solution was measured at above 200PPM of Chlorine during the inspection. Use chlorine test strips to confirm solution is at 100PPM. Corrected during the inspection. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
9-09-2021 Handwashing soap and single use towels or drying device shall be provided in dispensers adjacent to each handwashing facility; dispensers shall be maintained in good repair. (113953.2) Adequate separate facilities shall be provided for handwashing, food preparation, and the washing of utensils and equipment. (113953, 113953.1) 3.00 Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees. Employees shall not clean their hands in a sink used for food preparation, warewashing, or in a service sink or a curbed cleaning facility used for the disposal of mop water and similar liquid waste. Do not place objects in front of the handwashing station, and do not place items, utensils or wiping cloths in the handwashing sink.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Soap shall be provided in approved dispensers at, or adjacent to, handwashing facilities (no bars of soap). Single-use sanitary towels or hot-air blowers shall be provided at handwashing facilities in approved dispensing devices. 		Observed the facility does not have a faucet to allow for proper handwashing without touching. A faucet must be installed at the designated hand wash location. Currently there is a spray nozzle only. This must be done immediately for proper handwashing. Facility was informed of requirement and how to wash hands in the mean time. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
9-09-2021 The potable water supply shall be protected with a backflow or back siphonage protection device, as required by applicable plumbing codes. (114192) All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose. (114171, 114189.1, 114190, 114192.1, 114193, 114193.1, 114195, 114197, 114199, 114201, 114269) 1.00 All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. (CDI) Observed the max hot water temperature at the facility was measured at 116F during the inspection. ave the hot water heat evaluated and adjusted so it is at a minimum of 120F at the sink fixtures. Hot water was corrected during the inspection. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
9-09-2021 Food employees shall keep their hands and exposed portions of their arms clean, and shall maaintain fingernails so they are cleanable. Employees are required to wash their hands: before beginning work; before handling food / equipment / utensils; as often as necessary during food preparation to remove soil and contamination; when switching from working with raw to ready-to-eat foods; after touching body parts; after using the toilet room; or any time when contamination may occur. (113952, 113953.3, 113968, 113973 (a-g). Whenever gloves are worn, they shall be changed as often as handwashing is required. 7.00 The food employee shall wash their hands and portion of arms as required, and use utensils and gloves appropriately. (CDI) Observed employee washing their hands and then using a cotton towel to dry their hands and then throwing the towels back with the clean towels. Affected towels were removed. After washing hands a paper towel must be used to dry hands to prevent possible contamination when using a cotton towel. Facility was instructed on proper hand washing techniques. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)


Rating on date 9-25-2019: Satisfactory (Total Points: 13.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
9-25-2019 All food employees shall have adequate knowledge of and be trained in food safety as it relates to their assigned duties. The person in charge shall have adequate knowledge of, and shall educate employees of the food facility regarding major food allergens. (113947) Food facilities that prepare, handle or serve non-prepackaged potentially hazardous food, shall have an employee who has passed an approved food safety certification examination. (113947-113947.1) 2.00 The responsibilities of the staff member certified in food safety include ensuring that all employees who handle, or have responsibility for handling, unpackaged foods of any kind have sufficient knowledge to ensure the safe preparation and /or service of the food. The nature and extent of the knowledge that each employee is required to have may be tailored, as appropriate, to the employee's duties related to food safety issues. Observed lack of proof that a current employee of this establishment holds a Food Safety Manager Class certificate that is no more than five years old. Maintain a copy of the original certificate for at least one current employee at the facility location. The food managers certificate that is earned by the employee or owner may be used at only one location. Obtain a certificate from an American National Standards Institute approved food handling/food safety examination; if no one holds a current food safety certificate, obtain one within 60 days. All other employees must obtain a food handler card. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
9-25-2019 All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182) 2.00 Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.

Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.

The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated. 		Observed the white freezer next to the food prep fridge is still damaged and tape being used for repairs. Operator stated a new freezer has already been ordered. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
9-25-2019 Potentially hazardous foods shall be held at or below 41°/ 45°F or at or above 135°F. (113996, 113998, 114037, 114343(a)) 7.00 Hold potentially hazardous foods either at or above 135°F or at or below 41°F. Hold the following potentially hazardous foods at 45°F: raw shell eggs, unshucked live molluscan shellfish, pasteurized milk and pasteurized milk products in original, sealed containers. Potentially hazardous foods held for dispensing in a serving line or a salad bar (not in a display case) may be held at 45°F or less during periods not to exceed 12 hours in any 24-hour period. Discard all potentially hazardous food that has been out of an approved time and temperature range. Observed a stack of raw hamburger patties sitting out at room temperature near the grill. Hamburger patties was measured at 67F during inspection. Hamburger patties were removed from use during inspection and cannot be used. Keep all potentially hazardous food items at 41F and under or 135F and higher. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
9-25-2019 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 2.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method. 		Observed the lack of correct test strips at the facility for Quaternary Ammonia. Obtain the correct test strips to measure sanitizer solution. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)


Rating on date 8-27-2019: Unsatisfactory - reinspection required (Total Points: 17.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
8-27-2019 The potable water supply shall be protected with a backflow or back siphonage protection device, as required by applicable plumbing codes. (114192) All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose. (114171, 114189.1, 114190, 114192.1, 114193, 114193.1, 114195, 114197, 114199, 114201, 114269) 2.00 All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Observed lack of one inch minimum air gap between the drain lines under the three compartment sink and the rim height of the funnel drain. Repair or modify drain lines so that the distance between the lowest edge of the drain lines and the height of the floor sink rim allows for a minimum of a one inch air gap. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
8-27-2019 All food employees shall have adequate knowledge of and be trained in food safety as it relates to their assigned duties. The person in charge shall have adequate knowledge of, and shall educate employees of the food facility regarding major food allergens. (113947) Food facilities that prepare, handle or serve non-prepackaged potentially hazardous food, shall have an employee who has passed an approved food safety certification examination. (113947-113947.1) 2.00 The responsibilities of the staff member certified in food safety include ensuring that all employees who handle, or have responsibility for handling, unpackaged foods of any kind have sufficient knowledge to ensure the safe preparation and /or service of the food. The nature and extent of the knowledge that each employee is required to have may be tailored, as appropriate, to the employee's duties related to food safety issues. Observed lack of proof that a current employee of this establishment holds a Food Safety Manager Class certificate that is no more than five years old. Maintain a copy of the original certificate for at least one current employee at the facility location. The food managers certificate that is earned by the employee or owner may be used at only one location. Obtain a certificate from an American National Standards Institute approved food handling/food safety examination; if no one holds a current food safety certificate, obtain one within 60 days. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
8-27-2019 All food contact surfaces of utensils and equipment shall be clean and sanitized. (113984(e), 114097, 114099.1, 114099.4, 114099.6, 114101 (b-d), 114105, 114109, 114111, 114113, 114115 (a, b, d), 114117, 114125(b), 114135, 114141) 7.00 A food facility that prepares food shall not be operating if there is no method to properly clean and sanitize equipment or utensils. A food facility shall not be operating if there is gross contamination of food contact surfaces that may result in the contamination of food products. (CDI) Observed the use of pool chlorine to sanitize food contact surfaces. The chlorine at the facility is designed for pools only and not for use on food contact surfaces. Facility must discontinue use and obtain regular household chlorine for sanitizing food contact surfaces. A bottle was obtain during inspection. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
8-27-2019 Wiping cloths used to wipe service counters, scales or other surfaces that may come into contact with food shall be used only once unless kept in clean water with sanitizer. (114135, 114185, 114185.1, 11485.2, 114185.3) 2.00 Cloths used to wipe service counters, scales, and other surfaces that may directly or indirectly contact food shall be used only once until laundered or may be used repeatedly if held in a sanitizing solution, as described below. Cloths used with raw foods of animal origin shall be used only once until laundered or may be used repeatedly if kept in a separate container of sanitizing solution, as described below:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with the manufacturer's use directions. 		(CDI) Observed the lack of detectable sanitizer on the wiping cloths used to wipe cutting boards and other surfaces. Wiping cloths need to be kept in 100PPM of chlorine if reusing more than once. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
8-27-2019 Toilet facilities shall be maintained clean, sanitary and in good repair. Toilet rooms shall be separated by a well-fitting self-closing door. Toilet tissue shall be provided in a permanently installed dispenser at each toilet. The number of toilet facilities shall be in accordance with local building and plumbing ordinances. Toilet facilities shall be provided for patrons: in establishments with more than 20,000 sq ft.; establishments offering on-site food consumption. (113953, 113953.1, 113953.2, 114250, 114250.1, 114276) 2.00 Provide clean toilet facilities in good repair. Provide permanently installed toilet tissue dispenser(s) in all toilet facilities. Provide handwashing facilities within or adjacent to all toilet facilities. Soap shall be provided in dispensers at, or adjacent to, handwashing facilities. Single-use sanitary towels in dispensers or hot-air blowers shall be provided at handwashing facilities.

Customer restrooms are required for food facilities of more than 20,000 square feet if they were constructed after July 1 1984, and also applies to facilities of any size that were constructed after January 1, 2004 where there is onsite consumption of food. A "take-out only" food facility, with no seating indoors or outdoors, may not be required to provide customer restrooms. Check with the Division of Environmental Health and with the appropriate Planning Department before removing or restricting access to customer restrooms.
 Observed the restroom door is not self closing. Provide a self closing mechanism so restroom door fully closes.

Observed the fan unit inside the restroom is not functioning. Repair/replace unit so it is functioning and air is circulated inside the restroom. Toilet rooms shall be vented to the outside air by means of an openable, screened window, an air shaft, or a light-switch-activated exhaust fan, consistent with the requirements of local building codes. 		0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
8-27-2019 All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182) 2.00 Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.

Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.

The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated. 		Observed the use of tape to repair the gasket on the white chest freezer to the right of the food prep fridge unit. Repair/replace so it is in working order, smooth, and easily cleanable. Tape is not allowed. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)