Return To Restaurant Listing | Return to Environmental Health Homepage

Facility: Century Chevron #92388
Address: 1970 E Childs Ave, Merced, CA

The most recent inspection of this food facility resulted in a rating of
Satisfactory (Total Points: 10.00)
0-6  Points: Good
7-13 Points: Satisfactory
14+  Points: Unsatisfactory
Rating on date 11-09-2018: Satisfactory (Total Points: 10.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
11-09-2018 Toilet facilities shall be maintained clean, sanitary and in good repair. Toilet rooms shall be separated by a well-fitting self-closing door. Toilet tissue shall be provided in a permanently installed dispenser at each toilet. The number of toilet facilities shall be in accordance with local building and plumbing ordinances. Toilet facilities shall be provided for patrons: in establishments with more than 20,000 sq ft.; establishments offering on-site food consumption. (113953, 113953.1, 113953.2, 114250, 114250.1, 114276) 2.00 Provide clean toilet facilities in good repair. Provide permanently installed toilet tissue dispenser(s) in all toilet facilities. Provide handwashing facilities within or adjacent to all toilet facilities. Soap shall be provided in dispensers at, or adjacent to, handwashing facilities. Single-use sanitary towels in dispensers or hot-air blowers shall be provided at handwashing facilities.

Customer restrooms are required for food facilities of more than 20,000 square feet if they were constructed after July 1 1984, and also applies to facilities of any size that were constructed after January 1, 2004 where there is onsite consumption of food. A "take-out only" food facility, with no seating indoors or outdoors, may not be required to provide customer restrooms. Check with the Division of Environmental Health and with the appropriate Planning Department before removing or restricting access to customer restrooms.
Observed the lack of hot water at the hand wash station inside the restroom. Provide hot water at all times for proper hand washing. Water temperature was measured at a max of 77.5F during inspection. Repair. 0110 RETAIL MARKET<2000 SQ FT (HM3)
11-09-2018 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 4.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method.
(REPEAT VIOLATION 2) Observed the lack of test strips to measure sanitizer solution. Provide proper test strips to do so. Quaternary ammonia is used at the facility. Provide Quaternary Ammonia Test strips. 0110 RETAIL MARKET<2000 SQ FT (HM3)
11-09-2018 The walls / ceilings shall have durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair. (114065, 114067, 114069, 114175, 114143, 114257, 114259.2, 114266, 114268, 114268.1, 114271, 114272) 4.00 All food facilities shall be kept clean, fully operative, and in good repair. Floor surfaces in all areas in which food is prepared, packaged or stored, where any utensil is washed, where refuse or garbage is stored, where janitorial facilities are located, and in all restrooms and hand washing areas shall be smooth and of durable construction and made from non absorbent material that is easily cleanable.

Each permanent food facility shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. Food facilities that are not fully enclosed on all sides and that are in operation on January 1, 1985, shall not be required to meet the requirements of this section until the facility is remodeled or has a significant menu change or a change in its method of operation. Full enclosure is not required for dining areas and certain other areas when approved for outdoor food services.
(REPEAT VIOLATION 2) Observed broken/cracked/chipped tiles at the entrance to the back area with the three compartment sink, and one missing tile a the front entrance next to the cappuccino machine. Repair/replace tiles so the floor is smooth and easily cleanable. 0110 RETAIL MARKET<2000 SQ FT (HM3)


Rating on date 12-22-2017: Satisfactory (Total Points: 12.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
12-22-2017 Handwashing signs shall be posted in each toilet room, directing attention to the need to thoroughly wash hands after using the restroom. (113953.5)

No smoking signs shall be posted in food preparation, food storage, and warewashing areas. (113978)

Consumers shall be notified that clean tableware is to be used when they return to self-service areas such as salad bars and buffets. (114075)

Any food facility constructed before January 1, 2004 without public toilet facilities shall prominently post a sign within the food facility in a public area stating that toilet facilities are not provided. (113725.1, 114276, 114381 (e))
4.00 Post permit in a conspicuous place (It is recommended that the permit be in customer view.). Post a notice advising patrons that a copy of the most recent routine inspection report is available for review by interested parties. Keep a copy of the most recent health inspection report at the facility for customer review purposes.

Post and maintain a legible and conspicuous sign in each toilet room directing attention to the need to thoroughly wash hands after using the toilet.

Post and maintain a legible "No Smoking" sign in food preparation, food storage, and utensil washing areas.

Repeat: Observed lack of knowledge of the location of a copy of the most recent health inspection at the facility location. Maintain a copy of the most recent health inspection at the facility location, and ensure that employees are aware of its whereabouts and can provide a copy for customer inspection during all hours of operation. A new copy of most recent inspection report is being provided to the facility on this date. Corrected during inspection. 0110 RETAIL MARKET<2000 SQ FT (HM3)
12-22-2017 The walls / ceilings shall have durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair. (114065, 114067, 114069, 114175, 114143, 114257, 114259.2, 114266, 114268, 114268.1, 114271, 114272) 4.00 All food facilities shall be kept clean, fully operative, and in good repair. Floor surfaces in all areas in which food is prepared, packaged or stored, where any utensil is washed, where refuse or garbage is stored, where janitorial facilities are located, and in all restrooms and hand washing areas shall be smooth and of durable construction and made from non absorbent material that is easily cleanable.

Each permanent food facility shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. Food facilities that are not fully enclosed on all sides and that are in operation on January 1, 1985, shall not be required to meet the requirements of this section until the facility is remodeled or has a significant menu change or a change in its method of operation. Full enclosure is not required for dining areas and certain other areas when approved for outdoor food services.
Repeat: Observed cracked tiles throughout the market. Repair or replace to provide a smooth and easily cleanable surface. 0110 RETAIL MARKET<2000 SQ FT (HM3)
12-22-2017 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 4.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method.
2nd Repeat: Observed the lack of chlorine test strips at the facility. Bleach was the sanitizer observed at the facility with quat ammonia sanitizer. Provide the correct test strips for the sanitizer. 0110 RETAIL MARKET<2000 SQ FT (HM3)


Rating on date 11-08-2017: Unsatisfactory - reinspection required (Total Points: 18.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
11-08-2017 Handwashing signs shall be posted in each toilet room, directing attention to the need to thoroughly wash hands after using the restroom. (113953.5)

No smoking signs shall be posted in food preparation, food storage, and warewashing areas. (113978)

Consumers shall be notified that clean tableware is to be used when they return to self-service areas such as salad bars and buffets. (114075)

Any food facility constructed before January 1, 2004 without public toilet facilities shall prominently post a sign within the food facility in a public area stating that toilet facilities are not provided. (113725.1, 114276, 114381 (e))
2.00 Post permit in a conspicuous place (It is recommended that the permit be in customer view.). Post a notice advising patrons that a copy of the most recent routine inspection report is available for review by interested parties. Keep a copy of the most recent health inspection report at the facility for customer review purposes.

Post and maintain a legible and conspicuous sign in each toilet room directing attention to the need to thoroughly wash hands after using the toilet.

Post and maintain a legible "No Smoking" sign in food preparation, food storage, and utensil washing areas.

Observed lack of knowledge of the location of a copy of the most recent health inspection at the facility location. Maintain a copy of the most recent health inspection at the facility location, and ensure that employees are aware of its whereabouts and can provide a copy for customer inspection during all hours of operation. A new copy of most recent inspection report is being provided to the facility on this date. Corrected during inspection. 0110 RETAIL MARKET<2000 SQ FT (HM3)
11-08-2017 Any food is misbranded if its labeling is false or misleading, if it is offered for sale under the name of another food, or if it is an imitation of another food for which a definition and standard of identity has been established by regulation. (114087, 114089, 114089.1(a, b), 114090, 114093.1, 114377) 2.00 Present all food in a way that does not mislead or misinform consumers. Food or color additives, colored overwraps, lights or other misleading artificial means shall not be used to misrepresent the true appearance, color, or quality of a food.

The label shall contain the following information:
(1) The common name of the food.
(2) A list of ingredients in descending order of predominance by weight.
(3) The weight, count, or volume.
(4) The name and place of business of the manufacturer, packer, or distributor.
Nutrition labeling may also be required, and must be included when it is available from the manufacturer.

Food facility's or manufacturer's dating information, such as date codes or "use by" statements on packaging may not be concealed or altered.
Observed bagged ice that lacked proper labeling. Provide the required information as noted in the correction text. 0110 RETAIL MARKET<2000 SQ FT (HM3)
11-08-2017 All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182) 2.00 Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.

Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.

The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated.
Observed the ice scoop on the drain board next to a used towel. Utensils shall be stored in a manner to prevent contamination.

Observed the top plate of the ice machine has a accumulation of mold. Increase cleaning to prevent a accumulation of mold.

Observed the use of cardboard to line shelves. Remove, cardboard does not constitute a smooth and easily cleanable surface.
0110 RETAIL MARKET<2000 SQ FT (HM3)
11-08-2017 The walls / ceilings shall have durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair. (114065, 114067, 114069, 114175, 114143, 114257, 114259.2, 114266, 114268, 114268.1, 114271, 114272) 2.00 All food facilities shall be kept clean, fully operative, and in good repair. Floor surfaces in all areas in which food is prepared, packaged or stored, where any utensil is washed, where refuse or garbage is stored, where janitorial facilities are located, and in all restrooms and hand washing areas shall be smooth and of durable construction and made from non absorbent material that is easily cleanable.

Each permanent food facility shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. Food facilities that are not fully enclosed on all sides and that are in operation on January 1, 1985, shall not be required to meet the requirements of this section until the facility is remodeled or has a significant menu change or a change in its method of operation. Full enclosure is not required for dining areas and certain other areas when approved for outdoor food services.
Observed cracked tiles throughout the market. Repair or replace to provide a smooth and easily cleanable surface.

Observed tile missing where the toilet plumbing comes out of the wall. Repair or replace.
0110 RETAIL MARKET<2000 SQ FT (HM3)
11-08-2017 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 4.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method.
Repeat: Observed lack of correct test strips to measure the applicable manual sanitizer concentration. Obtain and use chlorine test strips to verify sanitizer is of sufficient strength to act as an appropriate manual sanitizing agent (100 ppm for chlorine, 200 ppm for quat ammonia). 0110 RETAIL MARKET<2000 SQ FT (HM3)
11-08-2017 All clean and soiled linens shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. (114185 - 114185.4) Utensils and equipment shall be handled and stored so as to be protected from contamination. (114067, 114074 - 114075, 114081, 114083, 114119, 114121, 114161, 114178, 114179, 114185, 114185.2, 114185.5) 2.00 Storage space for food, utensils, single-use articles, clean linens, and food-related equipment shall not be located in locker rooms, refuse rooms, mechanical rooms, under open stairwells, under lines on which water has condensed, under leaking water lines, under sewer lines that are not shielded to intercept potential drips, or under other sources of contamination.

During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored in one of the following ways:
(1) in a potentially hazardous food with their handles above the top of the food and the container.
(2) if not a potentially hazardous food, with their handles above the top of the food within containers that can be closed.
(3) on a clean portion of the food preparation table or equipment if cleaned and sanitized at the required frequency.
(4) in running water of sufficient velocity to flush particulates to the drain.
(5) in a clean, protected location if the utensils, such as ice scoops, are used only with a food that is not potentially hazardous.
(6) in a container of water if the water is maintained at a temperature of at least 135°F and the container is cleaned at least every 24 hours or at a frequency necessary to preclude the accumulation of soil residues.

Observed soiled towels on the floor beside the ice machine. Used towels shall be stored in an appropriate location. 0110 RETAIL MARKET<2000 SQ FT (HM3)
11-08-2017 All nonfood contact surfaces of utensils and equipment shall be clean. (114115, 114130.4) 2.00 Clean nonfood contact surfaces of equipment at a frequency necessary to prevent accumulation of residue. Observed build up of dust debris on the ceiling and around the display door frame in the walk-in refrigerator. Improve cleaning frequency so as to prevent a visible buildup of dust debris.

Observed a build up of debris between the furthest coke refrigerator and cabinet. Improve cleaning frequency so as to prevent a visible buildup of debris.

Observed a wood beam and a build up of debris under the two-compartment sink. Improve cleaning frequency so as to prevent a visible buildup of debris and remove all unnecessary items.
0110 RETAIL MARKET<2000 SQ FT (HM3)
11-08-2017 The potable water supply shall be protected with a backflow or back siphonage protection device, as required by applicable plumbing codes. (114192) All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose. (114171, 114189.1, 114190, 114192.1, 114193, 114193.1, 114195, 114197, 114199, 114201, 114269) 2.00 All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Observed lack of one inch minimum air gap between the drain lines under the two-compartment sink and the rim height of the floor sink. Repair or modify drain lines so that the distance between the lowest edge of the drain lines and the height of the floor sink rim allows for a minimum of a one inch air gap. 0110 RETAIL MARKET<2000 SQ FT (HM3)