Return To Restaurant Listing | Return to Environmental Health Homepage

Facility: Goodger Shell & Food Mart, Inc.
Address: 849 W Pacheco Blvd, Los Banos, CA

The most recent inspection of this food facility resulted in a rating of
Satisfactory (Total Points: 12.00)
0-6  Points: Good
7-13 Points: Satisfactory
14+  Points: Unsatisfactory
Rating on date 5-07-2019: Satisfactory (Total Points: 12.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
5-07-2019 The potable water supply shall be protected with a backflow or back siphonage protection device, as required by applicable plumbing codes. (114192) All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose. (114171, 114189.1, 114190, 114192.1, 114193, 114193.1, 114195, 114197, 114199, 114201, 114269) 2.00 All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. HANDWASHING STATION BEHIND THE REGISTER: No hot running water was available. Employee stated the hot water knob was stripped and the hot water valve underneath the sink was shut off. Repair or replace the hot water knob and provide hot running water. 0110 RETAIL MARKET<2000 SQ FT (HM3)
5-07-2019 All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182) 4.00 Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.

Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.

The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated.
1) 2-DOOR AQUAFINA REFRIGERATOR: Dust accumulation on the fan covers/guards. Mold accumulation on the undersides of some shelves. Clean.

2) WALK-IN REFRIGERATOR: Sticky residue/debris accumulation on the floor under shelving units. Clean. REPEAT VIOLATION

3) WALK-IN REFRIGERATOR: Dust accumulation on the fan covers/guards. Mold accumulation on some plastic beverage holders. Dried milk debris on the floor underneath the milk. Deep cleaning required.

4) INSIDE THE WHITE TRASHCAN CABINETS: Sticky residue/stains/food debris inside the cabinets. Clean.

5) WHITE CABINET UNDERNEATH THE CAPPUCCINO MACHINE: Repair the loose hinge so the door closes properly. REPEAT VIOLATION
0110 RETAIL MARKET<2000 SQ FT (HM3)
5-07-2019 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 2.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method.
3-COMPARTMENT DISHWASHING SINK: Provide sanitizer testing strips to measure the chlorine sanitizer concentration when washing dishes (soda nozzles, coffee filter cups, etc.). 0110 RETAIL MARKET<2000 SQ FT (HM3)
5-07-2019 Handwashing signs shall be posted in each toilet room, directing attention to the need to thoroughly wash hands after using the restroom. (113953.5)

No smoking signs shall be posted in food preparation, food storage, and warewashing areas. (113978)

Consumers shall be notified that clean tableware is to be used when they return to self-service areas such as salad bars and buffets. (114075)

Any food facility constructed before January 1, 2004 without public toilet facilities shall prominently post a sign within the food facility in a public area stating that toilet facilities are not provided. (113725.1, 114276, 114381 (e))
2.00 Post permit in a conspicuous place (It is recommended that the permit be in customer view.). Post a notice advising patrons that a copy of the most recent routine inspection report is available for review by interested parties. Keep a copy of the most recent health inspection report at the facility for customer review purposes.

Post and maintain a legible and conspicuous sign in each toilet room directing attention to the need to thoroughly wash hands after using the toilet.

Post and maintain a legible "No Smoking" sign in food preparation, food storage, and utensil washing areas.

1) WOMEN'S RESTROOM: Provide a handwashing sign.

2) MEN'S RESTROOM: Provide a handwashing sign.
0110 RETAIL MARKET<2000 SQ FT (HM3)
5-07-2019 The walls / ceilings shall have durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair. (114065, 114067, 114069, 114175, 114143, 114257, 114259.2, 114266, 114268, 114268.1, 114271, 114272) 2.00 All food facilities shall be kept clean, fully operative, and in good repair. Floor surfaces in all areas in which food is prepared, packaged or stored, where any utensil is washed, where refuse or garbage is stored, where janitorial facilities are located, and in all restrooms and hand washing areas shall be smooth and of durable construction and made from non absorbent material that is easily cleanable.

Each permanent food facility shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. Food facilities that are not fully enclosed on all sides and that are in operation on January 1, 1985, shall not be required to meet the requirements of this section until the facility is remodeled or has a significant menu change or a change in its method of operation. Full enclosure is not required for dining areas and certain other areas when approved for outdoor food services.
1) WALL NEXT TO THE BACK DOOR: Hole in the wall caused by the door handle. Repair hole and provide a smooth, easily cleanable, and nonabsorbent finish.

2) WALKWAY NEXT TO THE BACK DOOR: Heavily chipped corners exposing metal strips. Repair affected areas and provide smooth, easily cleanable, and nonabsorbent finishes.

3) FLOOR TO THE LEFT OF THE WALK-IN DOOR ENTRANCE: Sticky, dark residue and debris accumulation. Deep cleaning required.

4) WALL ACROSS THE SODA SYRUP RACK: Heavily chipped corners exposing metal strips. Repair affected areas and provide smooth, easily cleanable, and nonabsorbent finishes.

5) FLOOR UNDERNEATH THE SODA SYRUP RACK: Plastic caps and dust accumulation. Deep cleaning required.

6) 3-COMPARTMENT SINK AREA: Squeegees, paint roller, and paint tray stored inside the 2nd and 3rd sink compartments. Plastic crates stored on the right side drain board. Paint cans stored on the floor near the 2nd and 3rd compartments. Remove all items and keep sink free and accessible for washing dishes.
0110 RETAIL MARKET<2000 SQ FT (HM3)


Rating on date 12-06-2017: Satisfactory (Total Points: 10.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
12-06-2017 Handwashing soap and single use towels or drying device shall be provided in dispensers adjacent to each handwashing facility; dispensers shall be maintained in good repair. (113953.2) Adequate separate facilities shall be provided for handwashing, food preparation, and the washing of utensils and equipment. (113953, 113953.1) 2.00 Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees. Employees shall not clean their hands in a sink used for food preparation, warewashing, or in a service sink or a curbed cleaning facility used for the disposal of mop water and similar liquid waste. Do not place objects in front of the handwashing station, and do not place items, utensils or wiping cloths in the handwashing sink.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Soap shall be provided in approved dispensers at, or adjacent to, handwashing facilities (no bars of soap). Single-use sanitary towels or hot-air blowers shall be provided at handwashing facilities in approved dispensing devices.
HANDWASHING STATION BEHIND THE REGISTER: Replace the missing paper towel dispenser. 0110 RETAIL MARKET<2000 SQ FT (HM3)
12-06-2017 All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182) 4.00 Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.

Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.

The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated.
1) CABINET UNDERNEATH THE CAPPUCCINO MACHINE: Repair the loose hinge.

2) INSIDE THE CABINET STORING THE MOTOR FOR THE SODA MACHINE: Residue accumulation. Clean. Repeat violation.

3) INSIDE THE WALK-IN BEVERAGE REFRIGERATOR: Sticky residue/paper and plastic packaging materials on the floor under shelving units. Clean. Repeat violation.

4) INSIDE THE TRASH CAN CABINET: Residue accumulation. Clean. Repeat violation.
0110 RETAIL MARKET<2000 SQ FT (HM3)
12-06-2017 The walls / ceilings shall have durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair. (114065, 114067, 114069, 114175, 114143, 114257, 114259.2, 114266, 114268, 114268.1, 114271, 114272) 2.00 All food facilities shall be kept clean, fully operative, and in good repair. Floor surfaces in all areas in which food is prepared, packaged or stored, where any utensil is washed, where refuse or garbage is stored, where janitorial facilities are located, and in all restrooms and hand washing areas shall be smooth and of durable construction and made from non absorbent material that is easily cleanable.

Each permanent food facility shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. Food facilities that are not fully enclosed on all sides and that are in operation on January 1, 1985, shall not be required to meet the requirements of this section until the facility is remodeled or has a significant menu change or a change in its method of operation. Full enclosure is not required for dining areas and certain other areas when approved for outdoor food services.
1) SALES AREA: Replace the (2) moisture-damaged/stained ceiling panels.

2) ENTRANCE TO WALK-IN REFRIGERATION ROOM: Patch the hole in the wall caused by the door handle.

3) ENTRANCE TO WALK-IN REFRIGERATION ROOM: Repair the cracked/deteriorated wall corners.

4) MEN'S RESTROOM: Repair/secure the loose coving base tiles.

5) WOMEN'S RESTROOM: Repair/secure the loose coving base tiles.

6) 3-COMPARTMENT SINK ROOM: Repair the cracked/deteriorated wall corners.

7) BETWEEN THE HANDWASHING SINK AND THE MINI REDBULL REFRIGERATOR: Secure the loose floor tiles.
0110 RETAIL MARKET<2000 SQ FT (HM3)
12-06-2017 The premises of each food facility shall be kept clean and free of litter and rubbish; all clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept free of vermin. (114067 (j), 114123, 114143 (a) & (b), 114175, 114178, 114185, 114185.1, 114185.2, 114185.3, 114185.4, 114256, 114256.1, 114256.2, 114256.4, 114257, 114257.1, 114259, 114259.1, 114259.2, 114259.3, 114279, 114281, 114282) 2.00 All food facilities shall be kept clean, fully operative, and in good repair. A food facility shall at all times be so constructed, equipped, maintained, and operated as to prevent the entrance and harborage of animals, birds, and vermin, including, but not limited to, rodents and insects. The premises of each food facility shall be kept clean and free of litter, rubbish, and vermin.

Lockers or other suitable facilities shall be provided and used for the orderly storage of employee clothing and other possessions. Lockers or other suitable facilities shall be located in a designated room or area where contamination of food, equipment, utensils, linens, and single-use articles cannot occur. Dressing rooms or dressing areas shall be provided and used by employees if the employees regularly change their clothes in the facility.
3-COMPARTMENT SINK: Do not store dirty mops inside the compartment. 0110 RETAIL MARKET<2000 SQ FT (HM3)