Return To Restaurant Listing | Return to Environmental Health Homepage

Facility: Bella Nita's
Address: 2684 Shaffer Road, Atwater, CA

The most recent inspection of this food facility resulted in a rating of
Good (Total Points: 2.00)
0-6  Points: Good
7-13 Points: Satisfactory
14+  Points: Unsatisfactory
Rating on date 3-03-2025: Good (Total Points: 2.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
3-03-2025 All nonfood contact surfaces of utensils and equipment shall be clean. (114115, 114130.4) 1.00 Clean nonfood contact surfaces of equipment at a frequency necessary to prevent accumulation of residue. Observed dirt, grease, grime, and / or food particle buildup on the floor at the cooking area. Improve cleaning frequency and methods to ensure all area are cleanliness. 0103 FOOD ESTAB. W/FOOD PREP 150+ SEATS
3-03-2025 Exhaust hoods shall be provided to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6" beyond all cooking equipment. All areas shall have sufficient ventilation to facilitate proper food storage. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. (114149, 114149.1) Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields. (114149.2, 114149.3, 114252, 114252.1) 1.00 All areas shall have sufficient ventilation to facilitate proper food storage and to provide a reasonable condition of comfort for each employee, consistent with the job performed by the employee.

Light fixtures in areas where food is prepared, open food is stored, or utensils are cleaned shall be of shatterproof construction or shall be protected with shatterproof shields and shall be readily cleanable. In every room and area in which any food is prepared, manufactured, processed, or prepackaged, or in which equipment or utensils are cleaned, sufficient natural or artificial lighting shall be provided to produce the following light intensity, while the area is in use:
(a) At least 10-foot candles for the following:
(1) At a distance of 30 inches above the floor, in walk-in refrigeration units, and dry food storage areas.
(2) At a working surface on which alcoholic beverages are prepared or where utensils used in the preparation or service of alcoholic beverages are cleaned.
(3) Inside equipment, such as reach-in or under-the-counter refrigerators.
(b) At least 20-foot candles for the following:
(1) At a surface where food is provided for consumer self-service or where fresh produce or prepackaged foods are sold or offered for consumption.
(2) In server stations where food is prepared.
(3) At a distance of 30 inches above the floor in areas used for handwashing, warewashing, and equipment and utensil storage, and in toilet rooms.
(c) Except in server stations where food is prepared, at least 50-foot candles at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. 		Observed the light fixture in the exhaust hood does not function, bulb may be burned out. Replace bulb and / or repair fixture. Failure to provide adequate lighting. 0103 FOOD ESTAB. W/FOOD PREP 150+ SEATS


Rating on date 2-07-2025: Unsatisfactory - reinspection required (Total Points: 14.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
2-07-2025 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 1.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method. 		Observed the light fixture in the exhaust hood does not function, bulb may be burned out. Replace bulb and / or repair fixture. Failure to provide adequate lighting.

[7]Observed the walk in refrigerator is not working and owner is currently using a non commercial refrigerator as a back up. Remove non-commercial grade refrigerator, repair the walk in refrigerator and will need find a solution for refrigerating until walk in refrigerator is fix. 		0103 FOOD ESTAB. W/FOOD PREP 150+ SEATS
2-07-2025 Handwashing soap and single use towels or drying device shall be provided in dispensers adjacent to each handwashing facility; dispensers shall be maintained in good repair. (113953.2) Adequate separate facilities shall be provided for handwashing, food preparation, and the washing of utensils and equipment. (113953, 113953.1) 3.00 Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees. Employees shall not clean their hands in a sink used for food preparation, warewashing, or in a service sink or a curbed cleaning facility used for the disposal of mop water and similar liquid waste. Do not place objects in front of the handwashing station, and do not place items, utensils or wiping cloths in the handwashing sink.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Soap shall be provided in approved dispensers at, or adjacent to, handwashing facilities (no bars of soap). Single-use sanitary towels or hot-air blowers shall be provided at handwashing facilities in approved dispensing devices. 		Observed lack of paper towels in a functioning paper towel dispenser adjacent to the hand washing sink in the Kitchen. Provide a functioning paper towel dispenser adjacent to the handwashing sink and keep paper towel dispensers properly filled, or an air hand drying unit functional, to provide a sanitary method for hand drying at all times. (CDI) 0103 FOOD ESTAB. W/FOOD PREP 150+ SEATS
2-07-2025 All food shall be separated and protected from contamination. (113984, 113986, 113988, 113990, 114060, 114067, 114069, 114077, 114079, 114089.1 (c), 114143 (c)) 1.00 Destroy all contaminated food. All food shall be prepared, stored, displayed, dispensed, placed, transported, sold, and served as to be protected from dirt, vermin, unnecessary handling, droplet contamination, overhead leakage, or other contamination.
If unpackaged food is displayed and sold in bulk in other than self-service containers, then it shall be served by an employee of the food establishment directly to a consumer and shall be displayed in clean, sanitary, and covered or otherwise protected containers.
For bulk customer self-service food items, such as salad bars, buffet type foods, and other ready-to-eat food, install sneeze guards that intercept a direct line between the customer's mouth and the food being offered, dispense from approved mechanical dispensers, or employ other effective means to protect ready-to-eat food from contamination.
Protect all cartons, boxes, or other materials used in the packaging of any food from dirt, vermin, and other forms of contamination or adulteration. 		Observed rice in the refrigerated that was uncovered / not protected from potential contamination. Ensure all food not under diligent preparation is appropriately covered with non porous lid or covering material to protect from potential contamination. 0103 FOOD ESTAB. W/FOOD PREP 150+ SEATS
2-07-2025 Potentially hazardous foods shall be held at or below 41°/ 45°F or at or above 135°F. (113996, 113998, 114037, 114343(a)) 7.00 Hold potentially hazardous foods either at or above 135°F or at or below 41°F. Hold the following potentially hazardous foods at 45°F: raw shell eggs, unshucked live molluscan shellfish, pasteurized milk and pasteurized milk products in original, sealed containers. Potentially hazardous foods held for dispensing in a serving line or a salad bar (not in a display case) may be held at 45°F or less during periods not to exceed 12 hours in any 24-hour period. Discard all potentially hazardous food that has been out of an approved time and temperature range. Observed food such as beef, salsa, cheese are not properly held in the correct temperature in the non commercial refrigerator. Food temperature was measure at 47ºF-53ºF. Hold cold potentially hazardous food in the refrigerator at required temperatures at 41ºF or below at all times. Toss away all food that are have not been in range of 41ºF or below for more than 4 hours. Note: Walk in refrigerator was down from the previous day and a non commercial refrigerator was used. (CDI)
 0103 FOOD ESTAB. W/FOOD PREP 150+ SEATS
2-07-2025 Food shall be thawed under refrigeration, completely submerged under cold running water of sufficient velocity to flush loose particles, in a microwave oven, or during the cooking process. (114018, 114020, 114020.1) 1.00 Frozen potentially hazardous food shall only be thawed in one of the following ways:
(a) Under refrigeration that maintains the food temperature at 41°F or below.
(b) Completely submerged under potable running water for a period not to exceed two hours at a water temperature of 70°F or below, and with sufficient water velocity to agitate and flush off loose particles into the sink drain.
(c) In a microwave oven if immediately followed by immediate preparation.
(d) As part of a cooking process. 		Observed employee attempted to used hand washing sink to thaw shrimp. Employee was stop before the thawing. Failure to thaw potentially hazardous frozen foods in an approved manner. Retrain employee on thawing procedure. 0103 FOOD ESTAB. W/FOOD PREP 150+ SEATS
2-07-2025 All nonfood contact surfaces of utensils and equipment shall be clean. (114115, 114130.4) 1.00 Clean nonfood contact surfaces of equipment at a frequency necessary to prevent accumulation of residue. Observed dirt, grease, grime, and / or food particle buildup on the floor at the cooking area. Improve cleaning frequency and methods to ensure all area are cleanliness. 0103 FOOD ESTAB. W/FOOD PREP 150+ SEATS
2-07-2025 No violations were noted during this inspection. 0.00 This food facility currently meets California Retail Food Code requirements, and is authorized by the Merced County Division of Environmental Health to be open for business. The permit is issued to the current business owner of record and is non-transferable. Observed no violations noted during inspection. 0123 BAR


Rating on date 9-21-2021: Satisfactory (Total Points: 10.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
9-21-2021 All nonfood contact surfaces of utensils and equipment shall be clean. (114115, 114130.4) 1.00 Clean nonfood contact surfaces of equipment at a frequency necessary to prevent accumulation of residue. Observed the build up of grease/gunk on the deep fryer. Clean/sanitize and increase frequency to prevent build up. 0103 FOOD ESTAB. W/FOOD PREP 150+ SEATS
9-21-2021 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 1.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method. 		Observed the dishwashing machine spills water out of the top portion when turned on. Have the unit evaluated and repaired as necessary. 0103 FOOD ESTAB. W/FOOD PREP 150+ SEATS
9-21-2021 Exhaust hoods shall be provided to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6" beyond all cooking equipment. All areas shall have sufficient ventilation to facilitate proper food storage. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. (114149, 114149.1) Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields. (114149.2, 114149.3, 114252, 114252.1) 1.00 All areas shall have sufficient ventilation to facilitate proper food storage and to provide a reasonable condition of comfort for each employee, consistent with the job performed by the employee.

Light fixtures in areas where food is prepared, open food is stored, or utensils are cleaned shall be of shatterproof construction or shall be protected with shatterproof shields and shall be readily cleanable. In every room and area in which any food is prepared, manufactured, processed, or prepackaged, or in which equipment or utensils are cleaned, sufficient natural or artificial lighting shall be provided to produce the following light intensity, while the area is in use:
(a) At least 10-foot candles for the following:
(1) At a distance of 30 inches above the floor, in walk-in refrigeration units, and dry food storage areas.
(2) At a working surface on which alcoholic beverages are prepared or where utensils used in the preparation or service of alcoholic beverages are cleaned.
(3) Inside equipment, such as reach-in or under-the-counter refrigerators.
(b) At least 20-foot candles for the following:
(1) At a surface where food is provided for consumer self-service or where fresh produce or prepackaged foods are sold or offered for consumption.
(2) In server stations where food is prepared.
(3) At a distance of 30 inches above the floor in areas used for handwashing, warewashing, and equipment and utensil storage, and in toilet rooms.
(c) Except in server stations where food is prepared, at least 50-foot candles at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. 		Observed the fan unit inside the women's restroom is not functioning. Repair/replace to provide adequate air turnover. 0103 FOOD ESTAB. W/FOOD PREP 150+ SEATS
9-21-2021 All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182) 1.00 Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.

Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.

The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated. 		Observed the deep fryer was not properly positioned inside the perimeter of the hood unit. Adjust or remove any units so all heat producing equipment are in/under the hood unit. The fryer being outside of the hood unit has allowed oil/grease to accumulate on the ceiling adjacent to the hood.

Observed the build up of mildew on the white panel inside the ice machine. Clean/sanitize and increase frequency to prevent build up. 		0103 FOOD ESTAB. W/FOOD PREP 150+ SEATS
9-21-2021 The potable water supply shall be protected with a backflow or back siphonage protection device, as required by applicable plumbing codes. (114192) All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose. (114171, 114189.1, 114190, 114192.1, 114193, 114193.1, 114195, 114197, 114199, 114201, 114269) 1.00 All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Observed very low flow rate at the handwash sink in the bar area. Repair/replace so adequate flow is provided for proper hand washing.

Observed the build up of debris on the floor sink in the bar area. Clean and increase frequency to prevent build up. Drain lines may need to be brought lower to the floor sink to prevent splash of debris.

Observed a leak at underneath the three compartment sink in the bar area. Repair/replace so there is no longer a leak. 		0123 BAR
9-21-2021 Handwashing soap and single use towels or drying device shall be provided in dispensers adjacent to each handwashing facility; dispensers shall be maintained in good repair. (113953.2) Adequate separate facilities shall be provided for handwashing, food preparation, and the washing of utensils and equipment. (113953, 113953.1) 3.00 Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees. Employees shall not clean their hands in a sink used for food preparation, warewashing, or in a service sink or a curbed cleaning facility used for the disposal of mop water and similar liquid waste. Do not place objects in front of the handwashing station, and do not place items, utensils or wiping cloths in the handwashing sink.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Soap shall be provided in approved dispensers at, or adjacent to, handwashing facilities (no bars of soap). Single-use sanitary towels or hot-air blowers shall be provided at handwashing facilities in approved dispensing devices. 		(CDI Observed the hand washing sink located in the bar areas were blocked/filled with the sanitizer bucket. Do not block access to the hand washing sink. Keep it clear at all times so it might be used for proper hand washing. Sink was cleared out/unblocked during inspection. 0123 BAR
9-21-2021 The walls / ceilings shall have durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair. (114065, 114067, 114069, 114175, 114143, 114257, 114259.2, 114266, 114268, 114268.1, 114271, 114272) 2.00 All food facilities shall be kept clean, fully operative, and in good repair. Floor surfaces in all areas in which food is prepared, packaged or stored, where any utensil is washed, where refuse or garbage is stored, where janitorial facilities are located, and in all restrooms and hand washing areas shall be smooth and of durable construction and made from non absorbent material that is easily cleanable.

Each permanent food facility shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. Food facilities that are not fully enclosed on all sides and that are in operation on January 1, 1985, shall not be required to meet the requirements of this section until the facility is remodeled or has a significant menu change or a change in its method of operation. Full enclosure is not required for dining areas and certain other areas when approved for outdoor food services.
 (REPEAT VIOLATION) Observed the old bar area was removed and newer bar area has been installed. Flooring in the newer bar area has rubber top set coving. Remove and replace with an approved tiled cove base or other approved material. This includes the interior of the bar area and under the three compartment sink. 0123 BAR