Return To Restaurant Listing | Return to Environmental Health Homepage

Facility: La Morenita Market
Address: 705 H St., Los Banos, CA

The most recent inspection of this food facility resulted in a rating of
Satisfactory (Total Points: 12.00)
0-6  Points: Good
7-13 Points: Satisfactory
14+  Points: Unsatisfactory
Rating on date 11-07-2018: Satisfactory (Total Points: 12.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
11-07-2018 All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182) 0.00 Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.

Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.

The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated.
1) GRIDDLE AREA: Food debris accumulation on the table underneath the griddle. Deep cleaning required.

2) STEAM TABLE: Cutting board grooved and discolored, does not appear to come completely clean, and no longer constitutes a smooth and easily cleanable surface. Repair or replace damaged and discolored cutting boards; ensure that all food / utensil contact surfaces are smooth, easily cleanable, and nonporous.

3) 2-DOOR PREP REFRIGERATOR: Repair the right side door to properly close. The hinge may be loose and causing the door to bump into the left side door leaving the door opened and cold air to escape from the unit.

4) 2-DOOR PREP REFRIGERATOR: Cutting board grooved and discolored, does not appear to come completely clean, and no longer constitutes a smooth and easily cleanable surface. Repair or replace damaged and discolored cutting boards; ensure that all food / utensil contact surfaces are smooth, easily cleanable, and nonporous.

Violation points are already on the retail market program area.
0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
11-07-2018 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 0.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method.
3-COMPARTMENT SINK: Facility uses an ammonium chloride sanitizer (tablets) but had only chlorine sanitizer testing strips. Provide the correct sanitizer testing strips to measure the sanitizer concentration. Instruct all employees on how to measure the concentration. All food employees should be able to demonstrate proper dishwashing procedures.

Violation points are already on the retail market program area.
0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
11-07-2018 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 0.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method.
FLOUR ROOM 2-COMPARTMENT SINK: Provide sanitizer at this sink as buckets are cleaned here. (There was a gallon of sanitizer available in the next door tortilla room)

Violation points are already on the retail market program area.
0125 BAKERY
11-07-2018 No violations were noted during this inspection. 0.00 This food facility currently meets California Retail Food Code requirements, and is authorized by the Merced County Division of Environmental Health to be open for business. The permit is issued to the current business owner of record and is non-transferable. No violations noted in the open barbecue program area. 0148 OPEN-AIR BBQ
11-07-2018 All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182) 4.00 Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.

Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.

The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated.
1) ICE AND ICE CREAM FREEZER: Replace all cracked/deteriorated black seals/gaskets around the doors near the ice cream and ice bag areas. Do not use tape to repair.

2) WALK-IN MILK REFRIGERATOR: Remove all cardboard liners from the shelves and floor and discontinue this practice. They are not smooth, easily cleanable, and nonabsorbent.

3) ICE MACHINE: Mold accumulation on the white ice deflector. Clean and sanitize.

4) MEAT DEPT: Cutting boards grooved and discolored, does not appear to come completely clean, and no longer constitutes a smooth and easily cleanable surface. Repair or replace damaged and discolored cutting boards; ensure that all food / utensil contact surfaces are smooth, easily cleanable, and nonporous.
0111 RETAIL MARKET 2001-6000 SQFT
11-07-2018 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 4.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method.
MEAT DEPT 3-COMPARTMENT SINK: Repair (or provide proper, fitting drain plugs) the center and right compartment drain valves so as to be able to properly wash, rinse, and sanitize according to the correction text. Both valves do not hold water in the sink compartments when activated. 0111 RETAIL MARKET 2001-6000 SQFT
11-07-2018 Exhaust hoods shall be provided to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6" beyond all cooking equipment. All areas shall have sufficient ventilation to facilitate proper food storage. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. (114149, 114149.1) Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields. (114149.2, 114149.3, 114252, 114252.1) 4.00 All areas shall have sufficient ventilation to facilitate proper food storage and to provide a reasonable condition of comfort for each employee, consistent with the job performed by the employee.

Light fixtures in areas where food is prepared, open food is stored, or utensils are cleaned shall be of shatterproof construction or shall be protected with shatterproof shields and shall be readily cleanable. In every room and area in which any food is prepared, manufactured, processed, or prepackaged, or in which equipment or utensils are cleaned, sufficient natural or artificial lighting shall be provided to produce the following light intensity, while the area is in use:
(a) At least 10-foot candles for the following:
(1) At a distance of 30 inches above the floor, in walk-in refrigeration units, and dry food storage areas.
(2) At a working surface on which alcoholic beverages are prepared or where utensils used in the preparation or service of alcoholic beverages are cleaned.
(3) Inside equipment, such as reach-in or under-the-counter refrigerators.
(b) At least 20-foot candles for the following:
(1) At a surface where food is provided for consumer self-service or where fresh produce or prepackaged foods are sold or offered for consumption.
(2) In server stations where food is prepared.
(3) At a distance of 30 inches above the floor in areas used for handwashing, warewashing, and equipment and utensil storage, and in toilet rooms.
(c) Except in server stations where food is prepared, at least 50-foot candles at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor.
ICE AND ICE CREAM FREEZER: Replace several of the non-functioning light tubes near the glass doors. 0111 RETAIL MARKET 2001-6000 SQFT


Rating on date 9-27-2018: Unsatisfactory - reinspection required (Total Points: 25.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
9-27-2018 No violations were noted during this inspection. 0.00 This food facility currently meets California Retail Food Code requirements, and is authorized by the Merced County Division of Environmental Health to be open for business. The permit is issued to the current business owner of record and is non-transferable. No violations noted in the open barbecue program area. 0148 OPEN-AIR BBQ
9-27-2018 Handwashing soap and single use towels or drying device shall be provided in dispensers adjacent to each handwashing facility; dispensers shall be maintained in good repair. (113953.2) Adequate separate facilities shall be provided for handwashing, food preparation, and the washing of utensils and equipment. (113953, 113953.1) 2.00 Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees. Employees shall not clean their hands in a sink used for food preparation, warewashing, or in a service sink or a curbed cleaning facility used for the disposal of mop water and similar liquid waste. Do not place objects in front of the handwashing station, and do not place items, utensils or wiping cloths in the handwashing sink.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Soap shall be provided in approved dispensers at, or adjacent to, handwashing facilities (no bars of soap). Single-use sanitary towels or hot-air blowers shall be provided at handwashing facilities in approved dispensing devices.
FLOUR ROOM: Discontinue using the single burner propane stove to melt butter in this room. This is an unapproved activity. Propane stove is for outdoor use only and there is no exhaust hood to remove toxic gases, heat, vapor, and smoke. Remove from the facility. 0125 BAKERY
9-27-2018 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 0.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method.
1) FLOUR ROOM 2-COMPARTMENT SINK: Provide the (2) missing sink drain plugs so as to be able to properly wash, rinse, and sanitize dishes. All food employees shall be able to demonstrate proper dishwashing procedures.

2) FLOUR ROOM 2-COMPARTMENT SINK: Provide sanitizer at this sink as buckets are cleaned here.

3) FLOUR ROOM 2-COMPARTMENT SINK: Provide sanitizer testing strips to measure the sanitizer concentration when sanitizing dishes. Instruct all employees how to measure the concentration.

4) TORTILLA ROOM DISHWASHING SINK: Provide sanitizer at this sink as tools/utensils are cleaned here.

5) TORTILLA ROOM DISHWASHING SINK: Provide sanitizer testing strips to measure the sanitizer concentration when sanitizing dishes. Instruct all employees how to measure the concentration.

Violation points are already on the retail market program area.
0125 BAKERY
9-27-2018 Additional information provided to facility operators 0.00 Excerpts from California Health and Safety Code, Division 104 (Environmental Health), Part 7 (California Retail Food Code), sections 113700 through 114437. TORTILLA ROOM: Label the plastic bottle (per employee, water is inside the bottle) with a gray lid that has a hole located near the tortilla machine. 0125 BAKERY
9-27-2018 All clean and soiled linens shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. (114185 - 114185.4) Utensils and equipment shall be handled and stored so as to be protected from contamination. (114067, 114074 - 114075, 114081, 114083, 114119, 114121, 114161, 114178, 114179, 114185, 114185.2, 114185.5) 0.00 Storage space for food, utensils, single-use articles, clean linens, and food-related equipment shall not be located in locker rooms, refuse rooms, mechanical rooms, under open stairwells, under lines on which water has condensed, under leaking water lines, under sewer lines that are not shielded to intercept potential drips, or under other sources of contamination.

During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored in one of the following ways:
(1) in a potentially hazardous food with their handles above the top of the food and the container.
(2) if not a potentially hazardous food, with their handles above the top of the food within containers that can be closed.
(3) on a clean portion of the food preparation table or equipment if cleaned and sanitized at the required frequency.
(4) in running water of sufficient velocity to flush particulates to the drain.
(5) in a clean, protected location if the utensils, such as ice scoops, are used only with a food that is not potentially hazardous.
(6) in a container of water if the water is maintained at a temperature of at least 135°F and the container is cleaned at least every 24 hours or at a frequency necessary to preclude the accumulation of soil residues.

2-DOOR PREP REFRIGERATOR: A small plastic cup was used to scoop red salsa for customers. The same cup was used several times. Provide a proper scoop with a handle so there is no contamination.

Violation points are already on the retail market program area.
0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
9-27-2018 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 0.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method.
3-COMPARTMENT SINK: Facility uses an ammonium chloride sanitizer (tablets) but had only chlorine sanitizer testing strips. Provide the correct sanitizer testing strips to measure the sanitizer concentration. Instruct all employees on how to measure the concentration. All food employees should be able to demonstrate proper dishwashing procedures.

Violation points are already on the retail market program area.
0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
9-27-2018 Exhaust hoods shall be provided to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6" beyond all cooking equipment. All areas shall have sufficient ventilation to facilitate proper food storage. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. (114149, 114149.1) Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields. (114149.2, 114149.3, 114252, 114252.1) 0.00 All areas shall have sufficient ventilation to facilitate proper food storage and to provide a reasonable condition of comfort for each employee, consistent with the job performed by the employee.

Light fixtures in areas where food is prepared, open food is stored, or utensils are cleaned shall be of shatterproof construction or shall be protected with shatterproof shields and shall be readily cleanable. In every room and area in which any food is prepared, manufactured, processed, or prepackaged, or in which equipment or utensils are cleaned, sufficient natural or artificial lighting shall be provided to produce the following light intensity, while the area is in use:
(a) At least 10-foot candles for the following:
(1) At a distance of 30 inches above the floor, in walk-in refrigeration units, and dry food storage areas.
(2) At a working surface on which alcoholic beverages are prepared or where utensils used in the preparation or service of alcoholic beverages are cleaned.
(3) Inside equipment, such as reach-in or under-the-counter refrigerators.
(b) At least 20-foot candles for the following:
(1) At a surface where food is provided for consumer self-service or where fresh produce or prepackaged foods are sold or offered for consumption.
(2) In server stations where food is prepared.
(3) At a distance of 30 inches above the floor in areas used for handwashing, warewashing, and equipment and utensil storage, and in toilet rooms.
(c) Except in server stations where food is prepared, at least 50-foot candles at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor.
TAQUERIA EXHAUST HOOD: Replace the missing shatterproof cover over the light bulb.

Violation points are already on the retail market program area.
0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
9-27-2018 The walls / ceilings shall have durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair. (114065, 114067, 114069, 114175, 114143, 114257, 114259.2, 114266, 114268, 114268.1, 114271, 114272) 2.00 All food facilities shall be kept clean, fully operative, and in good repair. Floor surfaces in all areas in which food is prepared, packaged or stored, where any utensil is washed, where refuse or garbage is stored, where janitorial facilities are located, and in all restrooms and hand washing areas shall be smooth and of durable construction and made from non absorbent material that is easily cleanable.

Each permanent food facility shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. Food facilities that are not fully enclosed on all sides and that are in operation on January 1, 1985, shall not be required to meet the requirements of this section until the facility is remodeled or has a significant menu change or a change in its method of operation. Full enclosure is not required for dining areas and certain other areas when approved for outdoor food services.
2-DOOR TRAULSEN REFRIGERATOR AREA: Debris accumulation on the floor underneath the unit. Clean. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
9-27-2018 All poisonous substances, detergents, bleaches, and cleaning compounds shall be properly labeled and stored separate from food, utensils, packing material, and food-contact surfaces. (114254, 114254.1, 114254.2) 0.00 All poisonous substances, detergents, bleaches, cleaning compounds, and all other injurious or poisonous materials shall be stored and used only in a manner that is not likely to cause contamination or adulteration of food, food contact surfaces, utensils, or packaging materials. Poisonous or toxic materials shall be stored or displayed so they cannot contaminate food, equipment, utensils, linens, and single-use articles by separating the poisonous or toxic materials by spacing or partitioning and locating the poisonous or toxic materials in an area that is not above food, equipment, utensils, linens, and single-use articles. Equipment and utensil cleaners and sanitizers may be stored in warewashing areas for availability and convenience if the materials are stored to prevent contamination of food, equipment, utensils, linens, and single-use articles.

Containers of poisonous or toxic materials and personal care items shall bear a legible manufacturer's label. Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. A container previously used to store poisonous or toxic materials shall not be used to store, transport, or dispense food, utensils, and linen.

Only those insecticides, rodenticides and other pesticides that are specifically approved for use in a food facility may be used. The use shall be in accordance with manufacturer's instructions.
1) ORANGE CHEESE CONTAINER USED AS A SANITIZING BUCKET: Bucket was stored on the prep table . There was ongoing food preparation on the table. Store bucket on the floor so as to not contaminate food and food-contact areas.

2) ORANGE CHEESE CONTAINER USED AS A SANITIZING BUCKET: Remove the cheese label and properly label the bucket as sanitizer.

Violation points are already on the retail market program area.
0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
9-27-2018 Handwashing signs shall be posted in each toilet room, directing attention to the need to thoroughly wash hands after using the restroom. (113953.5)

No smoking signs shall be posted in food preparation, food storage, and warewashing areas. (113978)

Consumers shall be notified that clean tableware is to be used when they return to self-service areas such as salad bars and buffets. (114075)

Any food facility constructed before January 1, 2004 without public toilet facilities shall prominently post a sign within the food facility in a public area stating that toilet facilities are not provided. (113725.1, 114276, 114381 (e))
2.00 Post permit in a conspicuous place (It is recommended that the permit be in customer view.). Post a notice advising patrons that a copy of the most recent routine inspection report is available for review by interested parties. Keep a copy of the most recent health inspection report at the facility for customer review purposes.

Post and maintain a legible and conspicuous sign in each toilet room directing attention to the need to thoroughly wash hands after using the toilet.

Post and maintain a legible "No Smoking" sign in food preparation, food storage, and utensil washing areas.

WOMEN'S RESTROOM: Provide a handwashing sign.

MEN'S RESTROOM: Provide a handwashing sign.
0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
9-27-2018 All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182) 0.00 Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.

Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.

The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated.
1) NEAR THE SINGLE BURNER STOVE: Exposed electrical outlet. Provide a proper cover.

2) BLACK PANASONIC MICROWAVE: Rated for household use / not marked as rated for commercial use. Remove or replace all non commercially rated equipment. All new and replacement food-related and utensil-related equipment shall be certified or classified for sanitation by an American National Standards Institute (ANSI) accredited certification program / approved for commercial use.

3) BLACK CHIP CONTAINER: Container has heavy food debris accumulation on the exterior and a large hole on the side. The hole was patched with aluminum foil. Replace.

4) SINGLE BURNER STOVE: Replace the missing knobs.

5) GRIDDLE: Replace the missing knobs.

6) GRIDDLE: Oil tray was full and dripping onto a trash can located underneath it. Clean.

7) GRIDDLE AREA: Food debris accumulation on the table underneath the griddle. Deep cleaning required.

8) STEAM TABLE: Cutting board grooved and discolored, does not appear to come completely clean, and no longer constitutes a smooth and easily cleanable surface. Repair or replace damaged and discolored cutting boards; ensure that all food / utensil contact surfaces are smooth, easily cleanable, and nonporous.

9) 2-DOOR PREP REFRIGERATOR: Repair the right side door to properly close. The hinge may be loose and causing the door to bump into the left side door leaving the door opened and cold air to escape from the unit.

10) 2-DOOR PREP REFRIGERATOR: Cutting board grooved and discolored, does not appear to come completely clean, and no longer constitutes a smooth and easily cleanable surface. Repair or replace damaged and discolored cutting boards; ensure that all food / utensil contact surfaces are smooth, easily cleanable, and nonporous.

Violation points are already on the retail market program area.

0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
9-27-2018 All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182) 2.00 Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.

Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.

The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated.
1) ICE AND ICE CREAM FREEZER: Replace the (2) cracked/deteriorated black seals/gaskets around the first two doors near the ice cream area.

2) WALK-IN MILK REFRIGERATOR: Sticky residue and dried milk on the floor underneath the shelves. Deep cleaning required.

3) WALK-IN MILK REFRIGERATOR: Remove all cardboard liners from the shelves and floor and discontinue this practice. They are not smooth, easily cleanable, and nonabsorbent.

4) WALK-IN MEAT REFRIGERATOR: (2) rusty shelving units. Repair or replace to provide smooth, easily cleanable, and nonabsorbent surfaces.

5) WALK-IN MEAT REFRIGERATOR: Food debris and dried residue accumulation on the floor underneath shelving and pallets. Clean.

6) WALK-IN MEAT REFRIGERATOR: Remove all cardboard liners from the aluminum pallets and discontinue this practice. They are not smooth, easily cleanable, and nonabsorbent.

7) WALK-IN MEAT FREEZER: Food debris accumulation on the floor underneath shelving. Clean.

8) ICE MACHINE: Mold accumulation on the white ice deflector. Clean and sanitize.

9) MOP SINK AREA: Exposed electrical outlet. Provide a proper cover.

10) 2-DOOR LOS REFRESCOS DE MEXICO BEVERAGE REFRIGERATOR: Remove all cardboard liners from the shelves and discontinue this practice. They are not smooth, easily cleanable, and nonabsorbent.

11) MEAT DEPT: Cutting boards grooved and discolored, does not appear to come completely clean, and no longer constitutes a smooth and easily cleanable surface. Repair or replace damaged and discolored cutting boards; ensure that all food / utensil contact surfaces are smooth, easily cleanable, and nonporous.
0111 RETAIL MARKET 2001-6000 SQFT
9-27-2018 Additional information provided to facility operators 0.00 Excerpts from California Health and Safety Code, Division 104 (Environmental Health), Part 7 (California Retail Food Code), sections 113700 through 114437. 1) 16 OZ CREMA CONTAINERS IN THE CHEESE DISPLAY CASE: Discontinue repackaging creama from the large bucket into smaller 16 oz containers held in the display case. You do not have a dairy license to repackage pasteurized dairy products. You may put the crema into specific containers at the time the customer places the order only.

2) CUISINART COFFEE MACHINE: Remove the employee use coffee machine away from the business areas.
0111 RETAIL MARKET 2001-6000 SQFT
9-27-2018 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 2.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method.
MEAT DEPT 3-COMPARTMENT SINK: Repair the center and right compartment drain valves so as to be able to properly wash, rinse, and sanitize according to the correction text. Both valves do not hold water in the sink compartments when activated. 0111 RETAIL MARKET 2001-6000 SQFT
9-27-2018 All poisonous substances, detergents, bleaches, and cleaning compounds shall be properly labeled and stored separate from food, utensils, packing material, and food-contact surfaces. (114254, 114254.1, 114254.2) 7.00 All poisonous substances, detergents, bleaches, cleaning compounds, and all other injurious or poisonous materials shall be stored and used only in a manner that is not likely to cause contamination or adulteration of food, food contact surfaces, utensils, or packaging materials. Poisonous or toxic materials shall be stored or displayed so they cannot contaminate food, equipment, utensils, linens, and single-use articles by separating the poisonous or toxic materials by spacing or partitioning and locating the poisonous or toxic materials in an area that is not above food, equipment, utensils, linens, and single-use articles. Equipment and utensil cleaners and sanitizers may be stored in warewashing areas for availability and convenience if the materials are stored to prevent contamination of food, equipment, utensils, linens, and single-use articles.

Containers of poisonous or toxic materials and personal care items shall bear a legible manufacturer's label. Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. A container previously used to store poisonous or toxic materials shall not be used to store, transport, or dispense food, utensils, and linen.

Only those insecticides, rodenticides and other pesticides that are specifically approved for use in a food facility may be used. The use shall be in accordance with manufacturer's instructions.
WHITE CREMA CONTAINER USED AS A SANITIZING BUCKET: Remove the crema label and properly label the bucket as sanitizer. 0111 RETAIL MARKET 2001-6000 SQFT
9-27-2018 The potable water supply shall be protected with a backflow or back siphonage protection device, as required by applicable plumbing codes. (114192) All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose. (114171, 114189.1, 114190, 114192.1, 114193, 114193.1, 114195, 114197, 114199, 114201, 114269) 2.00 All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. 1) MOP SINK: The center vacuum breaker was leaking when the water was turned on. Repair.

2) MEAT DEPT HANDWASHING STATION: Black tape around the base of the faucet used to repair leak. Remove tape and properly repair faucet.

3) MEAT DEPT 3-COMPARTMENT SINK: Leak coming from underneath the left compartment drain pipe. Repair.

4) MEAT DEPT MEAT DISPLAY CASE: Raise the white pipes that do not have the required minimum 1 inch air gap between the rim of the floor sink and the end of the drain pipe.
0111 RETAIL MARKET 2001-6000 SQFT
9-27-2018 Exhaust hoods shall be provided to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6" beyond all cooking equipment. All areas shall have sufficient ventilation to facilitate proper food storage. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. (114149, 114149.1) Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields. (114149.2, 114149.3, 114252, 114252.1) 2.00 All areas shall have sufficient ventilation to facilitate proper food storage and to provide a reasonable condition of comfort for each employee, consistent with the job performed by the employee.

Light fixtures in areas where food is prepared, open food is stored, or utensils are cleaned shall be of shatterproof construction or shall be protected with shatterproof shields and shall be readily cleanable. In every room and area in which any food is prepared, manufactured, processed, or prepackaged, or in which equipment or utensils are cleaned, sufficient natural or artificial lighting shall be provided to produce the following light intensity, while the area is in use:
(a) At least 10-foot candles for the following:
(1) At a distance of 30 inches above the floor, in walk-in refrigeration units, and dry food storage areas.
(2) At a working surface on which alcoholic beverages are prepared or where utensils used in the preparation or service of alcoholic beverages are cleaned.
(3) Inside equipment, such as reach-in or under-the-counter refrigerators.
(b) At least 20-foot candles for the following:
(1) At a surface where food is provided for consumer self-service or where fresh produce or prepackaged foods are sold or offered for consumption.
(2) In server stations where food is prepared.
(3) At a distance of 30 inches above the floor in areas used for handwashing, warewashing, and equipment and utensil storage, and in toilet rooms.
(c) Except in server stations where food is prepared, at least 50-foot candles at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor.
ICE AND ICE CREAM FREEZER: Replace several of the non-functioning light tubes near the glass doors.

0111 RETAIL MARKET 2001-6000 SQFT
9-27-2018 Any food is misbranded if its labeling is false or misleading, if it is offered for sale under the name of another food, or if it is an imitation of another food for which a definition and standard of identity has been established by regulation. (114087, 114089, 114089.1(a, b), 114090, 114093.1, 114377) 2.00 Present all food in a way that does not mislead or misinform consumers. Food or color additives, colored overwraps, lights or other misleading artificial means shall not be used to misrepresent the true appearance, color, or quality of a food.

The label shall contain the following information:
(1) The common name of the food.
(2) A list of ingredients in descending order of predominance by weight.
(3) The weight, count, or volume.
(4) The name and place of business of the manufacturer, packer, or distributor.
Nutrition labeling may also be required, and must be included when it is available from the manufacturer.

Food facility's or manufacturer's dating information, such as date codes or "use by" statements on packaging may not be concealed or altered.
1) PREPARED MASA FOR 99 CENTS: Prepackaged and unlabeled. Provide proper labels with the manufacturer information, common food name, and ingredients.

2) PIÑA, CAMOTE, CALABAZA CLEAR CONTAINER NEAR THE REGISTER: Provide an ingredients label along with the common food name and manufacturer information or discontinue selling this product.

3) CHOCOLATES & DULCES CHARLY JARS NEAR THE REGISTERS: Ingredient labels for 3 jars state chile, sal, limon, azucar, frutas and common food name is dulce de tamarindo (candy of tamarind). Tamarind was not listed as an ingredient. One jar was not labeled. Provide proper labels to include manufacturer information and full ingredients in english or discontinue selling this product.

4) RED CANDIED PEANUTS: Unlabeled. Provide proper ingredients labels along with the common food names and manufacturer information or discontinue selling this product.

*All food must be from approved sources. No homemade products.
0111 RETAIL MARKET 2001-6000 SQFT
9-27-2018 All clean and soiled linens shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces. (114185 - 114185.4) Utensils and equipment shall be handled and stored so as to be protected from contamination. (114067, 114074 - 114075, 114081, 114083, 114119, 114121, 114161, 114178, 114179, 114185, 114185.2, 114185.5) 2.00 Storage space for food, utensils, single-use articles, clean linens, and food-related equipment shall not be located in locker rooms, refuse rooms, mechanical rooms, under open stairwells, under lines on which water has condensed, under leaking water lines, under sewer lines that are not shielded to intercept potential drips, or under other sources of contamination.

During pauses in food preparation or dispensing, food preparation and dispensing utensils shall be stored in one of the following ways:
(1) in a potentially hazardous food with their handles above the top of the food and the container.
(2) if not a potentially hazardous food, with their handles above the top of the food within containers that can be closed.
(3) on a clean portion of the food preparation table or equipment if cleaned and sanitized at the required frequency.
(4) in running water of sufficient velocity to flush particulates to the drain.
(5) in a clean, protected location if the utensils, such as ice scoops, are used only with a food that is not potentially hazardous.
(6) in a container of water if the water is maintained at a temperature of at least 135°F and the container is cleaned at least every 24 hours or at a frequency necessary to preclude the accumulation of soil residues.

ICE MACHINE: Ice scoop was stored on the plastic bags. Provide a smooth, easily cleanable, and nonabsorbent container to store and protect the ice scoop from contamination. 0111 RETAIL MARKET 2001-6000 SQFT