Return To Restaurant Listing | Return to Environmental Health Homepage

Facility: Little Diamond's Pizza
Address: 13104 Hwy 33 Ste B, Santa Nella, CA

The most recent inspection of this food facility resulted in a rating of
Satisfactory (Total Points: 8.00)
0-6  Points: Good
7-13 Points: Satisfactory
14+  Points: Unsatisfactory
Rating on date 11-27-2024: Satisfactory (Total Points: 8.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
11-27-2024 All food contact surfaces of utensils and equipment shall be clean and sanitized. (113984(e), 114097, 114099.1, 114099.4, 114099.6, 114101 (b-d), 114105, 114109, 114111, 114113, 114115 (a, b, d), 114117, 114125(b), 114135, 114141) 6.00 A food facility that prepares food shall not be operating if there is no method to properly clean and sanitize equipment or utensils. A food facility shall not be operating if there is gross contamination of food contact surfaces that may result in the contamination of food products. Repeat: Observed sponge in the prep sink. Sponges shall not be used in contact with cleaned and sanitized food-contact surfaces or in-use food-contact surfaces. Clean and sanitize all contaminated utensils and other surfaces. Discard all food which has been in contact with contaminated surfaces. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
11-27-2024 A food facility shall not be open for business without a valid permit. (114067(b) & (c), 114365, 114365.5, 114381, 114381.1 114381.2, 114387, 114390) 1.00 Pay the required annual permit fees. Renewal fees for existing permits for each calendar year are assessed and due in January of each year.

For purposes of enforcement, an enforcement officer may, during the facility's hours of operation and other reasonable times, enter, inspect, issue citations to, and secure any sample, photographs, or other evidence from a food facility or any facility suspected of being a food facility, or a vehicle transporting food to or from a retail food facility, when the vehicle is stationary at an agricultural inspection station, a border crossing, or at any food facility under the jurisdiction of the enforcement agency, or upon the request of an incident commander. It is a violation for any person to refuse to permit entry or inspection, or interfere with the performance of the duties of an enforcement officer, including making verbal or physical threats or sexual or discriminatory harassment.

Close the facility until a permit is obtained from the Division of Environmental Health. 		Observed lack of knowledge of the location of a copy of the most recent health inspection at the facility location. Maintain a copy of the most recent health inspection at the facility location, and ensure that employees are aware of its whereabouts and can provide a copy for customer inspection during all hours of operation. A new copy of most recent inspection report is being provided to the facility on this date. Corrected during inspection. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
11-27-2024 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 1.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method. 		Observed expired test strips. Obtain new test strip to verify manual sanitizing. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)


Rating on date 6-19-2023: Satisfactory (Total Points: 9.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
6-19-2023 All food employees shall have adequate knowledge of and be trained in food safety as it relates to their assigned duties. The person in charge shall have adequate knowledge of, and shall educate employees of the food facility regarding major food allergens. (113947) Food facilities that prepare, handle or serve non-prepackaged potentially hazardous food, shall have an employee who has passed an approved food safety certification examination. (113947-113947.1) 1.00 The responsibilities of the staff member certified in food safety include ensuring that all employees who handle, or have responsibility for handling, unpackaged foods of any kind have sufficient knowledge to ensure the safe preparation and /or service of the food. The nature and extent of the knowledge that each employee is required to have may be tailored, as appropriate, to the employee's duties related to food safety issues. Observed lack of knowledge for sanitizer strip testing. Retrain and provide all staff with proper training. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
6-19-2023 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 1.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method. 		Observed empty bottle of sanitizer for the sanitizer machine on the wall on top three compartment sink. Refill or replace with alternative. Corrected during inspection

Observed lack of test strips to measure the applicable manual sanitizer concentration. Obtain and use test strips to verify sanitizer is of sufficient strength to act as an appropriate manual sanitizing agent (100 ppm for chlorine, 200 ppm for quat ammonia). 		0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
6-19-2023 A food facility shall not be open for business without a valid permit. (114067(b) & (c), 114365, 114365.5, 114381, 114381.1 114381.2, 114387, 114390) 1.00 Pay the required annual permit fees. Renewal fees for existing permits for each calendar year are assessed and due in January of each year.

For purposes of enforcement, an enforcement officer may, during the facility's hours of operation and other reasonable times, enter, inspect, issue citations to, and secure any sample, photographs, or other evidence from a food facility or any facility suspected of being a food facility, or a vehicle transporting food to or from a retail food facility, when the vehicle is stationary at an agricultural inspection station, a border crossing, or at any food facility under the jurisdiction of the enforcement agency, or upon the request of an incident commander. It is a violation for any person to refuse to permit entry or inspection, or interfere with the performance of the duties of an enforcement officer, including making verbal or physical threats or sexual or discriminatory harassment.

Close the facility until a permit is obtained from the Division of Environmental Health. 		Observed lack of knowledge of the location of a copy of the most recent health inspection at the facility location. Maintain a copy of the most recent health inspection at the facility location, and ensure that employees are aware of its whereabouts and can provide a copy for customer inspection during all hours of operation. A new copy of most recent inspection report is being provided to the facility on this date. Corrected during inspection. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
6-19-2023 All food contact surfaces of utensils and equipment shall be clean and sanitized. (113984(e), 114097, 114099.1, 114099.4, 114099.6, 114101 (b-d), 114105, 114109, 114111, 114113, 114115 (a, b, d), 114117, 114125(b), 114135, 114141) 3.00 A food facility that prepares food shall not be operating if there is no method to properly clean and sanitize equipment or utensils. A food facility shall not be operating if there is gross contamination of food contact surfaces that may result in the contamination of food products. Observed sponges in the three compartment sink and employee stated the use of sponges to clean dishes. Cease practice immediately and find new alternative. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
6-19-2023 Handwashing soap and single use towels or drying device shall be provided in dispensers adjacent to each handwashing facility; dispensers shall be maintained in good repair. (113953.2) Adequate separate facilities shall be provided for handwashing, food preparation, and the washing of utensils and equipment. (113953, 113953.1) 3.00 Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees. Employees shall not clean their hands in a sink used for food preparation, warewashing, or in a service sink or a curbed cleaning facility used for the disposal of mop water and similar liquid waste. Do not place objects in front of the handwashing station, and do not place items, utensils or wiping cloths in the handwashing sink.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Soap shall be provided in approved dispensers at, or adjacent to, handwashing facilities (no bars of soap). Single-use sanitary towels or hot-air blowers shall be provided at handwashing facilities in approved dispensing devices. 		Observed lack of soap in the approved dispenser at the handwashing sink in the back kitchen. Keep an approved soap dispenser filled and functional at all times for handwashing purposes. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)


Rating on date 3-22-2021: Good (Total Points: 2.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
3-22-2021 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 1.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method. 		Observed lack of matching test strips to measure the applicable manual sanitizer concentration. Obtain and use test strips to verify sanitizer is of sufficient s/trength to act as an appropriate manual sanitizing agent (100 ppm for chlorine, 200 ppm for quat ammonia). Operator has test strips, unintentionally left at the Los Banos Little Diamonds location, to email picture of strips. {Photo of both chlorine sanitizer and test strips, and quat sanitizer and test strips, received via email on 3/28/21, corrected} 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
3-22-2021 All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182) 1.00 Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.

Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.

The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated. 		Observed two drain plugs present for the three compartment sink. Obtain and keep sufficient functional drain plugs for all compartments of the three compartment warewashing sink. {Photo of three drain plugs emailed 3/28/21, corrected} 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)