Return To Restaurant Listing | Return to Environmental Health Homepage

Facility: Major Golf Sports Center
Address: 3536 N. Santa Fe Dr., Merced, CA

The most recent inspection of this food facility resulted in a rating of
Satisfactory (Total Points: 13.00)
0-6  Points: Good
7-13 Points: Satisfactory
14+  Points: Unsatisfactory
Rating on date 8-14-2024: Satisfactory (Total Points: 13.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
8-14-2024 Handwashing soap and single use towels or drying device shall be provided in dispensers adjacent to each handwashing facility; dispensers shall be maintained in good repair. (113953.2) Adequate separate facilities shall be provided for handwashing, food preparation, and the washing of utensils and equipment. (113953, 113953.1) 3.00 Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees. Employees shall not clean their hands in a sink used for food preparation, warewashing, or in a service sink or a curbed cleaning facility used for the disposal of mop water and similar liquid waste. Do not place objects in front of the handwashing station, and do not place items, utensils or wiping cloths in the handwashing sink.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Soap shall be provided in approved dispensers at, or adjacent to, handwashing facilities (no bars of soap). Single-use sanitary towels or hot-air blowers shall be provided at handwashing facilities in approved dispensing devices. 		1. observed food prep hand wash sink did not have soap inside the dispenser. provide at all times.
2. Observed a lack of papertowels at the mens restroom. replace and keep stocked at all times.
 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
8-14-2024 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 2.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method. 		rpt 1.Observed that facility had lactic acid available but did not have proper test strips provide test strips at all times
2. Observed facility was using lactic acid to sanitize. Lactic acid use instructions is not provided in california retail food code provide documentation to indicate proper sanitizer strength, how to test sanitizer strength, and EPA reg number. 		0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
8-14-2024 The walls / ceilings shall have durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair. (114065, 114067, 114069, 114175, 114143, 114257, 114259.2, 114266, 114268, 114268.1, 114271, 114272) 1.00 All food facilities shall be kept clean, fully operative, and in good repair. Floor surfaces in all areas in which food is prepared, packaged or stored, where any utensil is washed, where refuse or garbage is stored, where janitorial facilities are located, and in all restrooms and hand washing areas shall be smooth and of durable construction and made from non absorbent material that is easily cleanable.

Each permanent food facility shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. Food facilities that are not fully enclosed on all sides and that are in operation on January 1, 1985, shall not be required to meet the requirements of this section until the facility is remodeled or has a significant menu change or a change in its method of operation. Full enclosure is not required for dining areas and certain other areas when approved for outdoor food services.
 1. Observed improvement. Facility replaced vinyl flooring in kitchen with tiles. the replacement was not like for like and a debirs accumulation point remains where tile was replaced. Repair broken vinyl floor with like for like. if not like for like reach out to MCDEH for guidance. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
8-14-2024 All food employees shall have adequate knowledge of and be trained in food safety as it relates to their assigned duties. The person in charge shall have adequate knowledge of, and shall educate employees of the food facility regarding major food allergens. (113947) Food facilities that prepare, handle or serve non-prepackaged potentially hazardous food, shall have an employee who has passed an approved food safety certification examination. (113947-113947.1) 6.00 The responsibilities of the staff member certified in food safety include ensuring that all employees who handle, or have responsibility for handling, unpackaged foods of any kind have sufficient knowledge to ensure the safe preparation and /or service of the food. The nature and extent of the knowledge that each employee is required to have may be tailored, as appropriate, to the employee's duties related to food safety issues. Observed FMC expired in 2023. replace. Repeat. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
8-14-2024 All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182) 1.00 Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.

Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.

The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated. 		1. observed true prep refrigerator was temped around 41F and the lid was no longer functioning properly. repair lid and gasket of this refrigerator to decrease prep bar temp. All equipment shall be well maintained.
2. Observed soda machine was draining to the floor sink below the 3-comp sink. repair so that this equipment drain has a 1in air gap above the flood rim of the floor sink. 		0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
8-14-2024 Failure of the person operating a food facility pursuant to a variance or HACCP plan to designate at least one person to be responsible for developing HACCP plans, verifying that HACCP plans are effective, and training employees to adhere to the designated HACCP plans. 0.00 A HACCP Plan is a written document that delineates the formal procedures developed for safe food handling approved by the National Advisory Committee on Microbiological Criterira for Foods (114419). A written document approving a deviation from standard health code requirements shall be maintained at the food facility. (114057, 114057.1, 114091(f)(3))

The person operating a food facility pursuant to a HACCP plan shall designate at least one person to be responsible for developing HACCP plans, verifying that HACCP plans are effective, and training employees.

A minimum of one person per shift shall be designated who is knowledgeable in the HACCP plan or plans adopted by the operator to be responsible for adherence to any HACCP plan used, take corrective actions when necessary, and assure monitoring records are appropriately documented and retained, per the requirements of section 114419. 		Provide "do not drink" water not potable sign at all sinks/ faucets or provide water system permit from state water resource control board. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)


Rating on date 1-31-2022: Satisfactory (Total Points: 9.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
1-31-2022 All food employees shall have adequate knowledge of and be trained in food safety as it relates to their assigned duties. The person in charge shall have adequate knowledge of, and shall educate employees of the food facility regarding major food allergens. (113947) Food facilities that prepare, handle or serve non-prepackaged potentially hazardous food, shall have an employee who has passed an approved food safety certification examination. (113947-113947.1) 3.00 The responsibilities of the staff member certified in food safety include ensuring that all employees who handle, or have responsibility for handling, unpackaged foods of any kind have sufficient knowledge to ensure the safe preparation and /or service of the food. The nature and extent of the knowledge that each employee is required to have may be tailored, as appropriate, to the employee's duties related to food safety issues. Observed lack of proof that a current employee of this establishment holds a Food Safety Manager Class certificate that is no more than five years old. Maintain a copy of the original certificate for at least one current employee at the facility location. The food managers certificate that is earned by the employee or owner may be used at only one location. Obtain a certificate from an American National Standards Institute approved food handling/food safety examination; if no one holds a current food safety certificate, obtain one within 60 days. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
1-31-2022 All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182) 1.00 Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.

Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.

The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated. 		Observed the silver upright true refrigerator was measured at 78F. Have the unit repaired/replaced so it is at 41F and under. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
1-31-2022 Handwashing soap and single use towels or drying device shall be provided in dispensers adjacent to each handwashing facility; dispensers shall be maintained in good repair. (113953.2) Adequate separate facilities shall be provided for handwashing, food preparation, and the washing of utensils and equipment. (113953, 113953.1) 3.00 Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees. Employees shall not clean their hands in a sink used for food preparation, warewashing, or in a service sink or a curbed cleaning facility used for the disposal of mop water and similar liquid waste. Do not place objects in front of the handwashing station, and do not place items, utensils or wiping cloths in the handwashing sink.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Soap shall be provided in approved dispensers at, or adjacent to, handwashing facilities (no bars of soap). Single-use sanitary towels or hot-air blowers shall be provided at handwashing facilities in approved dispensing devices. 		Observed the lack of paper towel in the dispenser at the hand wash station in the food prep area. Provide at all times for proper handwashing. Provide prior to opening. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
1-31-2022 The walls / ceilings shall have durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair. (114065, 114067, 114069, 114175, 114143, 114257, 114259.2, 114266, 114268, 114268.1, 114271, 114272) 1.00 All food facilities shall be kept clean, fully operative, and in good repair. Floor surfaces in all areas in which food is prepared, packaged or stored, where any utensil is washed, where refuse or garbage is stored, where janitorial facilities are located, and in all restrooms and hand washing areas shall be smooth and of durable construction and made from non absorbent material that is easily cleanable.

Each permanent food facility shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. Food facilities that are not fully enclosed on all sides and that are in operation on January 1, 1985, shall not be required to meet the requirements of this section until the facility is remodeled or has a significant menu change or a change in its method of operation. Full enclosure is not required for dining areas and certain other areas when approved for outdoor food services.
 Observed the flooring under the grill/four eye burner/stove is damaged and no longer smooth and easily cleanable. Repair/replace so the flooring is smooth and easily cleanable. Like for like material is ok, an other flooring will need to be submitted for approval and plan check. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
1-31-2022 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 1.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method. 		Observed lack of test strips to measure the applicable manual sanitizer concentration. Obtain and use test strips to verify sanitizer is of sufficient strength to act as an appropriate manual sanitizing agent (100 ppm for chlorine, 200 ppm for quat ammonia). 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)