Return To Restaurant Listing | Return to Environmental Health Homepage

Facility: O'Ryleighs Tavern
Address: 1730 Canal St., Merced, CA

The most recent inspection of this food facility resulted in a rating of
Satisfactory (Total Points: 10.00)
0-6  Points: Good
7-13 Points: Satisfactory
14+  Points: Unsatisfactory
Rating on date 3-05-2024: Satisfactory (Total Points: 10.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
3-05-2024 No violations were noted during this inspection. 0.00 This food facility currently meets California Retail Food Code requirements, and is authorized by the Merced County Division of Environmental Health to be open for business. The permit is issued to the current business owner of record and is non-transferable. No violations observed during the inspection. 0123 BAR
3-05-2024 Handwashing soap and single use towels or drying device shall be provided in dispensers adjacent to each handwashing facility; dispensers shall be maintained in good repair. (113953.2) Adequate separate facilities shall be provided for handwashing, food preparation, and the washing of utensils and equipment. (113953, 113953.1) 3.00 Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees. Employees shall not clean their hands in a sink used for food preparation, warewashing, or in a service sink or a curbed cleaning facility used for the disposal of mop water and similar liquid waste. Do not place objects in front of the handwashing station, and do not place items, utensils or wiping cloths in the handwashing sink.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Soap shall be provided in approved dispensers at, or adjacent to, handwashing facilities (no bars of soap). Single-use sanitary towels or hot-air blowers shall be provided at handwashing facilities in approved dispensing devices. 		Observed that hand washing sink is not easily accessible. Please have the hand washing sink easily accessible and functional. Please keep it clean. 0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
3-05-2024 Potentially hazardous foods shall be held at or below 41°/ 45°F or at or above 135°F. (113996, 113998, 114037, 114343(a)) 7.00 Hold potentially hazardous foods either at or above 135°F or at or below 41°F. Hold the following potentially hazardous foods at 45°F: raw shell eggs, unshucked live molluscan shellfish, pasteurized milk and pasteurized milk products in original, sealed containers. Potentially hazardous foods held for dispensing in a serving line or a salad bar (not in a display case) may be held at 45°F or less during periods not to exceed 12 hours in any 24-hour period. Discard all potentially hazardous food that has been out of an approved time and temperature range. Observed that the temperature of cheeses were measured 59 F. Operator did not use time control for perishable foods. Please use time control or keep close the lid of the salad bar. 0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS


Rating on date 9-06-2022: Satisfactory (Total Points: 12.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
9-06-2022 All food employees shall have adequate knowledge of and be trained in food safety as it relates to their assigned duties. The person in charge shall have adequate knowledge of, and shall educate employees of the food facility regarding major food allergens. (113947) Food facilities that prepare, handle or serve non-prepackaged potentially hazardous food, shall have an employee who has passed an approved food safety certification examination. (113947-113947.1) 6.00 The responsibilities of the staff member certified in food safety include ensuring that all employees who handle, or have responsibility for handling, unpackaged foods of any kind have sufficient knowledge to ensure the safe preparation and /or service of the food. The nature and extent of the knowledge that each employee is required to have may be tailored, as appropriate, to the employee's duties related to food safety issues. SECOND REPEAT (originally cited on 10/21/2021 inspection report): Observed lack of proof that a current employee of this establishment holds a Food Safety Manager Class certificate that is no more than five years old. Manager did state all employees were recently certified for the 'three year' cards, owner has copies in office. Maintain a copy of the required original five year certificate for at least one current employee at the facility location. The food managers certificate that is earned by the employee or owner may be used at only one location. Obtain a certificate from an American National Standards Institute approved food handling/food safety examination. Manager states cook (Alejandra) to obtain certificate, just found out she could complete the class online and is to complete class ASAP. Provide proof of class enrollment / completion by 9/14/22, and email a copy of the certificate once received (no later than 10/6/22). [Emailed photos of class sign up received 9/15/22, copy of certificate due to be emailed no later than 10/6/22]. 0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
9-06-2022 The walls / ceilings shall have durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair. (114065, 114067, 114069, 114175, 114143, 114257, 114259.2, 114266, 114268, 114268.1, 114271, 114272) 2.00 All food facilities shall be kept clean, fully operative, and in good repair. Floor surfaces in all areas in which food is prepared, packaged or stored, where any utensil is washed, where refuse or garbage is stored, where janitorial facilities are located, and in all restrooms and hand washing areas shall be smooth and of durable construction and made from non absorbent material that is easily cleanable.

Each permanent food facility shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. Food facilities that are not fully enclosed on all sides and that are in operation on January 1, 1985, shall not be required to meet the requirements of this section until the facility is remodeled or has a significant menu change or a change in its method of operation. Full enclosure is not required for dining areas and certain other areas when approved for outdoor food services.
 THIRD REPEAT: Observed damaged / missing VCT floor tiles in the liquor storage room. Repair / replace the missing and damaged tiles so as to provide a surface that is smooth and easily cleanable. Send photos of completed correction to FoodProgram@countyofmerced.com (please include your facility ID# 6144) no later than 9/14/22. [Emailed photos of VCT flooring correction received 9/15/22]
 0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
9-06-2022 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 2.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method. 		THIRD REPEAT: Observed facility still lacks quat test strips for the kitchen area three compartment sink. Test at three compartment sink does show "seven tablets" of quat sanitizer appears to have produced sanitizer of the correct strength. Facility is required to have the ability to test their required sanitizer strength directly themselves. Obtain and use DAILY the appropriate test strips for each type of sanitizer currently in use at this facility location (chlorine = 100 PPM for 30 seconds contact time, quat = 200 PPM for 60 seconds contact time). Send photo proof of quat test strips for this facility location no later than 9/14/22 to FoodProgram@countyofmerced.com (please include your facility ID #6144). [Emailed photos of quat sanitizer test strips being present in the facility received 9/15/2022] 0123 BAR
9-06-2022 The potable water supply shall be protected with a backflow or back siphonage protection device, as required by applicable plumbing codes. (114192) All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose. (114171, 114189.1, 114190, 114192.1, 114193, 114193.1, 114195, 114197, 114199, 114201, 114269) 2.00 All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. FOURTH REPEAT: Observed the continued lack of a one inch air gap for the plumbing between the bar mechanical washer and the rim height of the floor sink it drains into, and between the ice machine's drain line and the rim height of the same floor sink. Provide the required minimum one inch air gap. Send photo proof of correction to FoodProgram@countyofmerced.com (please include your facility ID #6144) no later than 9/14/22. [Emailed photos of air gap correction for equipment drain lines received 9/15/2022] 0123 BAR


Rating on date 8-04-2022: Unsatisfactory - reinspection required (Total Points: 19.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
8-04-2022 All food employees shall have adequate knowledge of and be trained in food safety as it relates to their assigned duties. The person in charge shall have adequate knowledge of, and shall educate employees of the food facility regarding major food allergens. (113947) Food facilities that prepare, handle or serve non-prepackaged potentially hazardous food, shall have an employee who has passed an approved food safety certification examination. (113947-113947.1) 3.00 The responsibilities of the staff member certified in food safety include ensuring that all employees who handle, or have responsibility for handling, unpackaged foods of any kind have sufficient knowledge to ensure the safe preparation and /or service of the food. The nature and extent of the knowledge that each employee is required to have may be tailored, as appropriate, to the employee's duties related to food safety issues. REPEAT (originally cited on 10/21/2021 inspection report): Observed lack of proof that a current employee of this establishment holds a Food Safety Manager Class certificate that is no more than five years old. Manager did state all employees were recently certified for the 'three year' cards, owner has copies in office. Maintain a copy of the required original five year certificate for at least one current employee at the facility location. The food managers certificate that is earned by the employee or owner may be used at only one location. Obtain a certificate from an American National Standards Institute approved food handling/food safety examination; if no one holds a current food safety certificate, obtain one within 60 days. 0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
8-04-2022 The walls / ceilings shall have durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair. (114065, 114067, 114069, 114175, 114143, 114257, 114259.2, 114266, 114268, 114268.1, 114271, 114272) 2.00 All food facilities shall be kept clean, fully operative, and in good repair. Floor surfaces in all areas in which food is prepared, packaged or stored, where any utensil is washed, where refuse or garbage is stored, where janitorial facilities are located, and in all restrooms and hand washing areas shall be smooth and of durable construction and made from non absorbent material that is easily cleanable.

Each permanent food facility shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. Food facilities that are not fully enclosed on all sides and that are in operation on January 1, 1985, shall not be required to meet the requirements of this section until the facility is remodeled or has a significant menu change or a change in its method of operation. Full enclosure is not required for dining areas and certain other areas when approved for outdoor food services.
 (1) Observed area where the previously identified damaged tiles in the walk-in refrigerator were located are now covered with particle board, broken tiles previously cited multiple times as needing repaired. Manager reports that walk in cooler repair is scheduled for this Sunday. Properly repair with approved materials, such as quarry tile. Floor surfaces in all areas in which food is prepared, packaged or stored, where any utensil is washed, where refuse or garbage is stored, where janitorial facilities are located, and in all restrooms and hand washing areas shall be smooth, easily cleanable, non porous, meet the required commercial grade standard, and be coved at the juncture of the floor and wall with a 3/8 inch minimum radius and shall extend up the wall at least 4 inches.

Also observed latching mechanism on walk in cooler is still broken, unclear if this is part of the planned repair this Sunday or not. Properly repair to the original commercial grade standard.

(2) SECOND REPEAT: Observed damaged / missing floor tiles in the liquor storage room. Repair.
 0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
8-04-2022 Handwashing signs shall be posted in each toilet room, directing attention to the need to thoroughly wash hands after using the restroom. (113953.5)

No smoking signs shall be posted in food preparation, food storage, and warewashing areas. (113978)

Consumers shall be notified that clean tableware is to be used when they return to self-service areas such as salad bars and buffets. (114075)

Any food facility constructed before January 1, 2004 without public toilet facilities shall prominently post a sign within the food facility in a public area stating that toilet facilities are not provided. (113725.1, 114276, 114381 (e)) 		2.00 Post permit in a conspicuous place (It is recommended that the permit be in customer view.). Post a notice advising patrons that a copy of the most recent routine inspection report is available for review by interested parties. Keep a copy of the most recent health inspection report at the facility for customer review purposes.

Post and maintain a legible and conspicuous sign in each toilet room directing attention to the need to thoroughly wash hands after using the toilet.

Post and maintain a legible "No Smoking" sign in food preparation, food storage, and utensil washing areas.

 (1) SECOND REPEAT: Observed lack of a handwashing reminder sign being posted in the mens restroom / still missing. Handwashing sign now also missing from the womens restroom. Post the required signs. 0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
8-04-2022 Food shall be stored in an approved manner, in approved containers and labeled as to contents. Food shall be stored at least 6" above the floor on approved shelving. (114047, 114049, 114051, 114053, 114055, 114067(h), 114069) 2.00 Provide adequate and suitable space for the storage of food. Store food at least 6 inches off the floor. Store bulk food not stored in original packaging in containers identifying the food by common name. Food shall not be stored in locker rooms, restrooms, dressing rooms, refuse areas, or mechanical rooms; under open stairwells; under lines on which water has condensed; under leaking water lines, including leaking automatic fire sprinkler heads: or under sewer lines that are not shielded to intercept potential drips.

Only prepackaged nonpotentially hazardous food or uncut produce may be displayed or sold outdoors by a food facility if outdoor displays have overhead protection that extends over all food items, and if all food items from the outdoor display are stored inside the fully enclosed food facility at all times other than during business hours.

Products that are held by the permit holder for credit, redemption, or return to the distributor, such as damaged, spoiled, or recalled products, shall be segregated and held in designated areas that are separated from food, equipment, utensils, linens, and single-use articles. All returned or damaged food products and food products from which the label has been removed shall be separated and stored in a separate area and in a manner that shall prevent adulteration of other foods and shall not contribute to a vermin problem.



 SECOND REPEAT: Observed jugs of oil sitting directly on the floor in the dry storage area. Also observed container of cut french fries sitting directly on the floor in the walk in cooler. Ensure ALL food and food related items (such as 'to go' containers) are stored at least six inches off the floor in a manner so as to protect them from potential contamination. 0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
8-04-2022 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 2.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method. 		SECOND REPEAT: Observed facility still lacks quat test strips for the kitchen area three compartment sink. Obtain and use DAILY the appropriate test strips for each type of sanitizer currently in use at this facility location (chlorine = 100 PPM for 30 seconds contact time, quat = 200 PPM for 60 seconds contact time). 0123 BAR
8-04-2022 The potable water supply shall be protected with a backflow or back siphonage protection device, as required by applicable plumbing codes. (114192) All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose. (114171, 114189.1, 114190, 114192.1, 114193, 114193.1, 114195, 114197, 114199, 114201, 114269) 2.00 All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. THIRD REPEAT: Observed the continued lack of a one inch air gap for the plumbing between the bar mechanical washer and the rim height of the floor sink it drains into, and between the ice machine's drain line and the rim height of the same floor sink. Provide the required minimum one inch air gap. 0123 BAR
8-04-2022 Handwashing soap and single use towels or drying device shall be provided in dispensers adjacent to each handwashing facility; dispensers shall be maintained in good repair. (113953.2) Adequate separate facilities shall be provided for handwashing, food preparation, and the washing of utensils and equipment. (113953, 113953.1) 6.00 Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees. Employees shall not clean their hands in a sink used for food preparation, warewashing, or in a service sink or a curbed cleaning facility used for the disposal of mop water and similar liquid waste. Do not place objects in front of the handwashing station, and do not place items, utensils or wiping cloths in the handwashing sink.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Soap shall be provided in approved dispensers at, or adjacent to, handwashing facilities (no bars of soap). Single-use sanitary towels or hot-air blowers shall be provided at handwashing facilities in approved dispensing devices. 		FOURTH REPEAT: Observed an appropriate enclosed paper towel dispenser has been installed by the south handwash sink behind the bar. The north handwash sink location still has a household style open dispenser. Replace the open dispenser with one that is enclosed / protected that only allow the user to touch the paper towels they are using, or a hot air blowing unit for the north bar hand washing station. Provide a sanitary hand drying method at each handwashing sink location. 0123 BAR


Rating on date 11-30-2021: Unsatisfactory - reinspection required (Total Points: 29.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
11-30-2021 Failure to keep food pure and free from contamination, adulteration and spoilage. Any food is adulterated if it bears or contains any poisonous or deleterious substance that may render it impure or injurious to health. (113967, 113976, 113980, 113988, 113990, 114035, 114254(c), 114254.3) 7.00 Provide adequate protection at all times to keep food pure and free from contamination, adulteration and spoilage. Destroy all contaminated, adulterated and spoiled food. Observed metal open can in the corner of the ice bin used to scoop ice into glasses behind the bar. When asked, employee stated that she places cans in the corner when mixing multiple back to back drinks using the same mixer. Cease this practice. ce that has been used as a medium for cooling exterior surfaces of items such as melons, fish, prepackaged foods, bottled or canned beverages, or cooling coils and tubes of equipment shall not be used as food or in drinks. Can removed from ice bin and ice in the corner where the can was scooped out and discarded. Corrected during inspection. 0123 BAR
11-30-2021 Handwashing soap and single use towels or drying device shall be provided in dispensers adjacent to each handwashing facility; dispensers shall be maintained in good repair. (113953.2) Adequate separate facilities shall be provided for handwashing, food preparation, and the washing of utensils and equipment. (113953, 113953.1) 6.00 Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees. Employees shall not clean their hands in a sink used for food preparation, warewashing, or in a service sink or a curbed cleaning facility used for the disposal of mop water and similar liquid waste. Do not place objects in front of the handwashing station, and do not place items, utensils or wiping cloths in the handwashing sink.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Soap shall be provided in approved dispensers at, or adjacent to, handwashing facilities (no bars of soap). Single-use sanitary towels or hot-air blowers shall be provided at handwashing facilities in approved dispensing devices. 		THIRD REPEAT: Observed the lack of paper towels in an appropriate paper towel dispenser (enclosed / protected that only allow the user to touch the paper towels they are using / NOT an open 'household' style paper towel holder) or a hot air blowing unit for the bar hand washing stations. Provide a sanitary hand drying method at each handwashing sink location. 0123 BAR
11-30-2021 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 2.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method. 		REPEAT: Observed facility now has test strips for the bar dish machine (chlorine), but still lacks quat test strips for the kitchen area three compartment sink. Obtain and use DAILY the appropriate test strips for each type of sanitizer currently in use at this facility location. 0123 BAR
11-30-2021 All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182) 2.00 Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.

Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.

The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated. 		(1) SECOND REPEAT: Observed soda gun on right 'door' side of bar is still sticky. Improve cleaning frequency to prevent the accumulation of visible residue.

(2) REPEAT: Observed black residue buildup on the lip of the deflector plate in the ice machine is still present. Increase cleaning and sanitizing frequency to prevent the accumulation of visible residue.

(3) REPEAT: Observed food particulate buildup near seals of 3 section slide top cooler behind bar is still present. Unit is empty, may not be in use. Increase cleaning frequency so as to prevent the accumulation of visible residue and possible vermin attraction. If equipment is unused and no longer needed, remove the unit from the facility to prevent unintended vermin harborage.

(4) Observed latch / handle mechanism on walk in cooler door is broken. Repair or replace. 		0123 BAR
11-30-2021 The potable water supply shall be protected with a backflow or back siphonage protection device, as required by applicable plumbing codes. (114192) All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose. (114171, 114189.1, 114190, 114192.1, 114193, 114193.1, 114195, 114197, 114199, 114201, 114269) 2.00 All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. SECOND REPEAT: Observed the continued lack of a one inch air gap for the plumbing between the bar mechanical washer and ice machine. Provide a one inch air gap. 0123 BAR
11-30-2021 Food shall be stored in an approved manner, in approved containers and labeled as to contents. Food shall be stored at least 6" above the floor on approved shelving. (114047, 114049, 114051, 114053, 114055, 114067(h), 114069) 2.00 Provide adequate and suitable space for the storage of food. Store food at least 6 inches off the floor. Store bulk food not stored in original packaging in containers identifying the food by common name. Food shall not be stored in locker rooms, restrooms, dressing rooms, refuse areas, or mechanical rooms; under open stairwells; under lines on which water has condensed; under leaking water lines, including leaking automatic fire sprinkler heads: or under sewer lines that are not shielded to intercept potential drips.

Only prepackaged nonpotentially hazardous food or uncut produce may be displayed or sold outdoors by a food facility if outdoor displays have overhead protection that extends over all food items, and if all food items from the outdoor display are stored inside the fully enclosed food facility at all times other than during business hours.

Products that are held by the permit holder for credit, redemption, or return to the distributor, such as damaged, spoiled, or recalled products, shall be segregated and held in designated areas that are separated from food, equipment, utensils, linens, and single-use articles. All returned or damaged food products and food products from which the label has been removed shall be separated and stored in a separate area and in a manner that shall prevent adulteration of other foods and shall not contribute to a vermin problem.



 REPEAT: Observed to-go containers in a plastic sleeve and plastic jugs of syrups sitting directly on the floor in the dry storage area at the back of the kitchen. Ensure that all food is stored on smooth and easily cleanable storage surfaces that are a minimum of six inches off the floor. 0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
11-30-2021 Handwashing signs shall be posted in each toilet room, directing attention to the need to thoroughly wash hands after using the restroom. (113953.5)

No smoking signs shall be posted in food preparation, food storage, and warewashing areas. (113978)

Consumers shall be notified that clean tableware is to be used when they return to self-service areas such as salad bars and buffets. (114075)

Any food facility constructed before January 1, 2004 without public toilet facilities shall prominently post a sign within the food facility in a public area stating that toilet facilities are not provided. (113725.1, 114276, 114381 (e)) 		2.00 Post permit in a conspicuous place (It is recommended that the permit be in customer view.). Post a notice advising patrons that a copy of the most recent routine inspection report is available for review by interested parties. Keep a copy of the most recent health inspection report at the facility for customer review purposes.

Post and maintain a legible and conspicuous sign in each toilet room directing attention to the need to thoroughly wash hands after using the toilet.

Post and maintain a legible "No Smoking" sign in food preparation, food storage, and utensil washing areas.

 (1) REPEAT: Observed lack of a visibly posted notice to inform patrons that the facility is inspected by the local health department. Maintain a sign in a conspicuous location to inform patrons that the facility is inspected. (A copy of the required notice is available on the Merced County Environmental Health website). Copy provided during inspection, immediately posted. Corrected during inspection.

(2) REPEAT: Observed lack of knowledge of the location of a copy of the most recent health inspection at the facility location. Maintain a copy of the most recent health inspection at the facility location, and ensure that employees are aware of its whereabouts and can provide a copy for customer inspection during all hours of operation. Reviewed with employees the ability to locate / pull up a copy of their most recent inspection report online from the Merced County Environmental Health website. A new copy of most recent inspection report is also being sent to the facility on this date. Corrected during inspection.

(3) REPEAT: Observed lack of a handwashing reminder sign being posted in the mens restroom / still missing. Provide the required sign. 		0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
11-30-2021 The walls / ceilings shall have durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair. (114065, 114067, 114069, 114175, 114143, 114257, 114259.2, 114266, 114268, 114268.1, 114271, 114272) 2.00 All food facilities shall be kept clean, fully operative, and in good repair. Floor surfaces in all areas in which food is prepared, packaged or stored, where any utensil is washed, where refuse or garbage is stored, where janitorial facilities are located, and in all restrooms and hand washing areas shall be smooth and of durable construction and made from non absorbent material that is easily cleanable.

Each permanent food facility shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. Food facilities that are not fully enclosed on all sides and that are in operation on January 1, 1985, shall not be required to meet the requirements of this section until the facility is remodeled or has a significant menu change or a change in its method of operation. Full enclosure is not required for dining areas and certain other areas when approved for outdoor food services.
 (1) FOURTH REPEAT: Observed the tiles in the walk-in refrigerator are still damaged. Repair.

(2) THIRD REPEAT: Observed damaged / missing floor tiles in the southwest corners behind the bar. Repair. Note, damaged tiles in northwest corner behind bar have been replaced but leak still appears to exist / liquid is already pooling on top of new tiles and may continue to cause damage / erode grout.

(3) REPEAT: Observed damaged / missing floor tiles in the liquor storage room. Repair. 		0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
11-30-2021 All food employees shall have adequate knowledge of and be trained in food safety as it relates to their assigned duties. The person in charge shall have adequate knowledge of, and shall educate employees of the food facility regarding major food allergens. (113947) Food facilities that prepare, handle or serve non-prepackaged potentially hazardous food, shall have an employee who has passed an approved food safety certification examination. (113947-113947.1) 0.00 The responsibilities of the staff member certified in food safety include ensuring that all employees who handle, or have responsibility for handling, unpackaged foods of any kind have sufficient knowledge to ensure the safe preparation and /or service of the food. The nature and extent of the knowledge that each employee is required to have may be tailored, as appropriate, to the employee's duties related to food safety issues. REMINDER (originally cited on inspection report on 10/21/2021): Observed lack of proof that a current employee of this establishment holds a Food Safety Manager Class certificate that is no more than five years old. Maintain a copy of the original certificate for at least one current employee at the facility location. The food managers certificate that is earned by the employee or owner may be used at only one location. Obtain a certificate from an American National Standards Institute approved food handling/food safety examination; if no one holds a current food safety certificate, obtain one within 60 days / by the original deadline of 12/20/2021. 0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
11-30-2021 All nonfood contact surfaces of utensils and equipment shall be clean. (114115, 114130.4) 2.00 Clean nonfood contact surfaces of equipment at a frequency necessary to prevent accumulation of residue. (1) REPEAT: Observed residue buildup on the wall below the manifold for the soda syrup lines (in the back storage room) is still present. Improve cleaning frequency and efficacy so as to prevent the accumulation of visible residue and potential rodent attraction.

(2) REPEAT: Observed visible grease residue buildup under the hood in the kitchen area is still present. Improve cleaning frequency and efficacy so as to prevent the accumulation of visible residue and potential fire hazard.

(3) REPEAT: Observed visible buildup on the FRP wall surface near the french fry cutting unit is still present. Improve cleaning frequency and efficacy so as to prevent the accumulation of visible residue and potential rodent attraction.

(4) REPEAT: Observed visible accumulation of residue around cooking equipment including pot stove, char broiler, fryers, and similar is still present. Improve cleaning frequency and efficacy beneath, behind, and around all cooking equipment so as to prevent the accumulation of visible residue and potential rodent attraction. 		0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
11-30-2021 Exhaust hoods shall be provided to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6" beyond all cooking equipment. All areas shall have sufficient ventilation to facilitate proper food storage. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. (114149, 114149.1) Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields. (114149.2, 114149.3, 114252, 114252.1) 2.00 All areas shall have sufficient ventilation to facilitate proper food storage and to provide a reasonable condition of comfort for each employee, consistent with the job performed by the employee.

Light fixtures in areas where food is prepared, open food is stored, or utensils are cleaned shall be of shatterproof construction or shall be protected with shatterproof shields and shall be readily cleanable. In every room and area in which any food is prepared, manufactured, processed, or prepackaged, or in which equipment or utensils are cleaned, sufficient natural or artificial lighting shall be provided to produce the following light intensity, while the area is in use:
(a) At least 10-foot candles for the following:
(1) At a distance of 30 inches above the floor, in walk-in refrigeration units, and dry food storage areas.
(2) At a working surface on which alcoholic beverages are prepared or where utensils used in the preparation or service of alcoholic beverages are cleaned.
(3) Inside equipment, such as reach-in or under-the-counter refrigerators.
(b) At least 20-foot candles for the following:
(1) At a surface where food is provided for consumer self-service or where fresh produce or prepackaged foods are sold or offered for consumption.
(2) In server stations where food is prepared.
(3) At a distance of 30 inches above the floor in areas used for handwashing, warewashing, and equipment and utensil storage, and in toilet rooms.
(c) Except in server stations where food is prepared, at least 50-foot candles at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. 		REPEAT: Observed light in the kitchen over the three compartment sink is still very dim, appears at least one of the bulbs in the fixture is burned out or not functioning. Investigate and repair. 0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS


Rating on date 10-21-2021: Unsatisfactory - reinspection required (Total Points: 27.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
10-21-2021 An adequate, protected, pressurized, potable supply of hot water and cold water shall be provided at all times. (113953(c), 114099.2(b) 114101(a), 114189, 114192, 114192.1, 114195) 7.00 Provide hot and cold water under pressure through a mixing valve to each sink compartment. The water supply shall be from a water system approved by the health officer or the state department. An adequate, protected, pressurized, potable supply of hot water, at least 120°F, and cold water shall be provided.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees 		Observed initial check of water temperature at kitchen 3 compartment sink was reading 102 degrees. Hot water heater checked / adjusted / made sure pilot is lit, recheck after approximately 30 minutes shows water now at 135 degrees. Provide hot and cold water under pressure through a mixing valve to the janitorial sink. Hot water shall be at least 120ºF. Corrected during inspection. 0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
10-21-2021 Handwashing signs shall be posted in each toilet room, directing attention to the need to thoroughly wash hands after using the restroom. (113953.5)

No smoking signs shall be posted in food preparation, food storage, and warewashing areas. (113978)

Consumers shall be notified that clean tableware is to be used when they return to self-service areas such as salad bars and buffets. (114075)

Any food facility constructed before January 1, 2004 without public toilet facilities shall prominently post a sign within the food facility in a public area stating that toilet facilities are not provided. (113725.1, 114276, 114381 (e)) 		1.00 Post permit in a conspicuous place (It is recommended that the permit be in customer view.). Post a notice advising patrons that a copy of the most recent routine inspection report is available for review by interested parties. Keep a copy of the most recent health inspection report at the facility for customer review purposes.

Post and maintain a legible and conspicuous sign in each toilet room directing attention to the need to thoroughly wash hands after using the toilet.

Post and maintain a legible "No Smoking" sign in food preparation, food storage, and utensil washing areas.

 (1) Observed lack of a visibly posted notice to inform patrons that the facility is inspected by the local health department. Maintain a sign in a conspicuous location to inform patrons that the facility is inspected. (A copy of the required notice is available on the Merced County Environmental Health website).

(2) Observed lack of knowledge of the location of a copy of the most recent health inspection at the facility location. Maintain a copy of the most recent health inspection at the facility location, and ensure that employees are aware of its whereabouts and can provide a copy for customer inspection during all hours of operation. A new copy of most recent inspection report is being provided to the facility on this date. Corrected during inspection.

(3) Observed lack of a handwashing reminder sign being posted in the mens restroom. Provide the required sign. 		0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
10-21-2021 All nonfood contact surfaces of utensils and equipment shall be clean. (114115, 114130.4) 1.00 Clean nonfood contact surfaces of equipment at a frequency necessary to prevent accumulation of residue. (1) Observed residue buildup on the wall below the manifold for the soda syrup lines (in the back storage room). Improve cleaning frequency and efficacy so as to prevent the accumulation of visible residue and potential rodent attraction.

(2) Observed visible grease residue buildup under the hood in the kitchen area. Improve cleaning frequency and efficacy so as to prevent the accumulation of visible residue and potential fire hazard.

(3) Observed visible buildup on the FRP wall surface near the french fry cutting unit. Improve cleaning frequency and efficacy so as to prevent the accumulation of visible residue and potential rodent attraction.

(4) Observed visible accumulation of residue around cooking equipment including pot stove, char broiler, fryers, and similar. Improve cleaning frequency and efficacy beneath, behind, and around all cooking equipment so as to prevent the accumulation of visible residue and potential rodent attraction. 		0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
10-21-2021 Food shall be stored in an approved manner, in approved containers and labeled as to contents. Food shall be stored at least 6" above the floor on approved shelving. (114047, 114049, 114051, 114053, 114055, 114067(h), 114069) 1.00 Provide adequate and suitable space for the storage of food. Store food at least 6 inches off the floor. Store bulk food not stored in original packaging in containers identifying the food by common name. Food shall not be stored in locker rooms, restrooms, dressing rooms, refuse areas, or mechanical rooms; under open stairwells; under lines on which water has condensed; under leaking water lines, including leaking automatic fire sprinkler heads: or under sewer lines that are not shielded to intercept potential drips.

Only prepackaged nonpotentially hazardous food or uncut produce may be displayed or sold outdoors by a food facility if outdoor displays have overhead protection that extends over all food items, and if all food items from the outdoor display are stored inside the fully enclosed food facility at all times other than during business hours.

Products that are held by the permit holder for credit, redemption, or return to the distributor, such as damaged, spoiled, or recalled products, shall be segregated and held in designated areas that are separated from food, equipment, utensils, linens, and single-use articles. All returned or damaged food products and food products from which the label has been removed shall be separated and stored in a separate area and in a manner that shall prevent adulteration of other foods and shall not contribute to a vermin problem.



 Observed to-go containers in a plastic sleeve and plastic jugs of syrups sitting directly on the floor in the dry storage area at the back of the kitchen. Ensure that all food is stored on smooth and easily cleanable storage surfaces that are a minimum of six inches off the floor. 0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
10-21-2021 Exhaust hoods shall be provided to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6" beyond all cooking equipment. All areas shall have sufficient ventilation to facilitate proper food storage. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. (114149, 114149.1) Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields. (114149.2, 114149.3, 114252, 114252.1) 1.00 All areas shall have sufficient ventilation to facilitate proper food storage and to provide a reasonable condition of comfort for each employee, consistent with the job performed by the employee.

Light fixtures in areas where food is prepared, open food is stored, or utensils are cleaned shall be of shatterproof construction or shall be protected with shatterproof shields and shall be readily cleanable. In every room and area in which any food is prepared, manufactured, processed, or prepackaged, or in which equipment or utensils are cleaned, sufficient natural or artificial lighting shall be provided to produce the following light intensity, while the area is in use:
(a) At least 10-foot candles for the following:
(1) At a distance of 30 inches above the floor, in walk-in refrigeration units, and dry food storage areas.
(2) At a working surface on which alcoholic beverages are prepared or where utensils used in the preparation or service of alcoholic beverages are cleaned.
(3) Inside equipment, such as reach-in or under-the-counter refrigerators.
(b) At least 20-foot candles for the following:
(1) At a surface where food is provided for consumer self-service or where fresh produce or prepackaged foods are sold or offered for consumption.
(2) In server stations where food is prepared.
(3) At a distance of 30 inches above the floor in areas used for handwashing, warewashing, and equipment and utensil storage, and in toilet rooms.
(c) Except in server stations where food is prepared, at least 50-foot candles at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. 		Observed light in the kitchen over the three compartment sink is very dim, appears at least one of the bulbs in the fixture is burned out or not functioning. Investigate and repair. 0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
10-21-2021 The walls / ceilings shall have durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair. (114065, 114067, 114069, 114175, 114143, 114257, 114259.2, 114266, 114268, 114268.1, 114271, 114272) 2.00 All food facilities shall be kept clean, fully operative, and in good repair. Floor surfaces in all areas in which food is prepared, packaged or stored, where any utensil is washed, where refuse or garbage is stored, where janitorial facilities are located, and in all restrooms and hand washing areas shall be smooth and of durable construction and made from non absorbent material that is easily cleanable.

Each permanent food facility shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. Food facilities that are not fully enclosed on all sides and that are in operation on January 1, 1985, shall not be required to meet the requirements of this section until the facility is remodeled or has a significant menu change or a change in its method of operation. Full enclosure is not required for dining areas and certain other areas when approved for outdoor food services.
 (1) THIRD REPEAT: Observed the tiles in the walk-in refrigerator is damaged. Repair.

(2) SECOND REPEAT: Observed damaged / missing floor tiles in the northwest and southwest corners behind the bar. Repair.

(3) Observed damaged / missing floor tiles in the liquor storage room. Repair. 		0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
10-21-2021 All food employees shall have adequate knowledge of and be trained in food safety as it relates to their assigned duties. The person in charge shall have adequate knowledge of, and shall educate employees of the food facility regarding major food allergens. (113947) Food facilities that prepare, handle or serve non-prepackaged potentially hazardous food, shall have an employee who has passed an approved food safety certification examination. (113947-113947.1) 3.00 The responsibilities of the staff member certified in food safety include ensuring that all employees who handle, or have responsibility for handling, unpackaged foods of any kind have sufficient knowledge to ensure the safe preparation and /or service of the food. The nature and extent of the knowledge that each employee is required to have may be tailored, as appropriate, to the employee's duties related to food safety issues. Observed lack of proof that a current employee of this establishment holds a Food Safety Manager Class certificate that is no more than five years old. Maintain a copy of the original certificate for at least one current employee at the facility location. The food managers certificate that is earned by the employee or owner may be used at only one location. Obtain a certificate from an American National Standards Institute approved food handling/food safety examination; if no one holds a current food safety certificate, obtain one within 60 days. 0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
10-21-2021 Handwashing soap and single use towels or drying device shall be provided in dispensers adjacent to each handwashing facility; dispensers shall be maintained in good repair. (113953.2) Adequate separate facilities shall be provided for handwashing, food preparation, and the washing of utensils and equipment. (113953, 113953.1) 6.00 Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees. Employees shall not clean their hands in a sink used for food preparation, warewashing, or in a service sink or a curbed cleaning facility used for the disposal of mop water and similar liquid waste. Do not place objects in front of the handwashing station, and do not place items, utensils or wiping cloths in the handwashing sink.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Soap shall be provided in approved dispensers at, or adjacent to, handwashing facilities (no bars of soap). Single-use sanitary towels or hot-air blowers shall be provided at handwashing facilities in approved dispensing devices. 		SECOND REPEAT: Observed the lack of paper towels in an appropriate paper towel dispensers or a hot air blowing unit for the bar hand washing stations. Provide a sanitary hand drying method at all handwashing sink locations. 0123 BAR
10-21-2021 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 1.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method. 		(1) Observed lack of sanitizer of sufficient strength on dishes in the bar area dish machine (25 PPM chlorine). Instructed employee in manual sanitizing techniques. Perform manual sanitization of all dishes at this location at the prescribed ppm (parts per million) for the sanitization method in use (see corrective text). Use the correct test strips for the chemical sanitizer being used. Check the sanitizer strength at a sufficient frequency to ensure consistent sanitization of all food contact surfaces in this location. Repairman immediately called, replaced cracked line, now measuring at 50+PPM chlorine. Corrected during inspection.

(2) Observed lack of test strips to measure the applicable manual sanitizer concentration. Obtain and use test strips to verify sanitizer is of sufficient strength to act as an appropriate manual sanitizing agent (100 ppm for chlorine in the dish machine, 200 ppm for quat ammonia at the three compartment sink and in the rag buckets). 		0123 BAR
10-21-2021 All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182) 2.00 Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.

Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.

The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated. 		(1) REPEAT: Observed soda gun on right 'door' side of bar is sticky, may be damaged, accumulation in holder cup. Improve cleaning frequency to prevent the accumulation of visible residue. Employee states the soda gun is scheduled to be replaced by vendor.

(2) Observed three compartment sink behind the bar is missing the faucet, sink has an accumulation of straws, not functional. Employee reports all glasses from bar are run thru dish machine, and second three compartment sink is present in kitchen. Replace, remove or repair non functional sink behind bar.

(3) Observed small amount of residue buildup on the lip of the deflector plate in the ice machine. Increase cleaning and sanitizing frequency to prevent the accumulation of visible residue.

(4) Observed food particulate buildup near seals of 3 section slide top cooler behind bar. Unit is empty, may not be in use. Increase cleaning frequency so as to prevent the accumulation of visible residue and possible vermin attraction. If equipment is unused and no longer needed, remove the unit from the facility to prevent unintended vermin harborage. 		0123 BAR
10-21-2021 The potable water supply shall be protected with a backflow or back siphonage protection device, as required by applicable plumbing codes. (114192) All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose. (114171, 114189.1, 114190, 114192.1, 114193, 114193.1, 114195, 114197, 114199, 114201, 114269) 2.00 All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. REPEAT: Observed the lack of a one inch air gap for the plumbing between the bar mechanical washer and ice machine. Provide a one inch air gap. 0123 BAR