| 4-27-2021 |
The potable water supply shall be protected with a backflow or back siphonage protection device, as required by applicable plumbing codes. (114192) All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose. (114171, 114189.1, 114190, 114192.1, 114193, 114193.1, 114195, 114197, 114199, 114201, 114269)
| 1.00 |
All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair.
|
Observed the hand wash sink near the register lacking cold water. Water temperature at the hand wash sink was measured above 108F. Repair so cold water is working at the hand wash sink. Cold water was found to be turned off. Cold water turned on during the inspection.
|
0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
|
| 4-27-2021 |
Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125)
| 1.00 |
Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.
Clean the utensils in one of the following ways:
(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.
(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.
Provide testing equipment and materials to adequately measure the applicable sanitization method.
|
(CDI) Observed the lack of soap connected to the dish washing machine. Provide soap at all times for proper utensil washing. Soap was replaced during the inspection.
|
0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
|
| 4-27-2021 |
All nonfood contact surfaces of utensils and equipment shall be clean. (114115, 114130.4)
| 1.00 |
Clean nonfood contact surfaces of equipment at a frequency necessary to prevent accumulation of residue.
|
Observed the build up of dust/debris on the fan blade covers inside all the small under counter fridge units. Clean/sanitize and increase frequency to prevent build up.
|
0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
|
| 4-27-2021 |
Potentially hazardous foods shall be held at or below 41°/ 45°F or at or above 135°F. (113996, 113998, 114037, 114343(a))
| 3.00 |
Hold potentially hazardous foods either at or above 135°F or at or below 41°F. Hold the following potentially hazardous foods at 45°F: raw shell eggs, unshucked live molluscan shellfish, pasteurized milk and pasteurized milk products in original, sealed containers. Potentially hazardous foods held for dispensing in a serving line or a salad bar (not in a display case) may be held at 45°F or less during periods not to exceed 12 hours in any 24-hour period. Discard all potentially hazardous food that has been out of an approved time and temperature range.
|
Observed the small under counter fridge unit was measured at 46F during the inspection. Have the unit evaluated and repaired as necessary so it is at 41F and under. All food items were moved to a different unit. Keep all potentially hazardous food items at 41F and under.
|
0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
|