Return To Restaurant Listing | Return to Environmental Health Homepage

Facility: El Grullense Jal #4
Address: 2053 E. Pacheco Blvd, Los Banos, CA

The most recent inspection of this food facility resulted in a rating of
Satisfactory (Total Points: 12.00)
0-6  Points: Good
7-13 Points: Satisfactory
14+  Points: Unsatisfactory
Rating on date 4-19-2024: Satisfactory (Total Points: 12.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
4-19-2024 No violations were noted during this inspection. 0.00 This food facility currently meets California Retail Food Code requirements, and is authorized by the Merced County Division of Environmental Health to be open for business. The permit is issued to the current business owner of record and is non-transferable. no violations observed. 0145 COMMISSARY / OPEN FOOD PREP ALLOWED
4-19-2024 Handwashing signs shall be posted in each toilet room, directing attention to the need to thoroughly wash hands after using the restroom. (113953.5)

No smoking signs shall be posted in food preparation, food storage, and warewashing areas. (113978)

Consumers shall be notified that clean tableware is to be used when they return to self-service areas such as salad bars and buffets. (114075)

Any food facility constructed before January 1, 2004 without public toilet facilities shall prominently post a sign within the food facility in a public area stating that toilet facilities are not provided. (113725.1, 114276, 114381 (e)) 		1.00 Post permit in a conspicuous place (It is recommended that the permit be in customer view.). Post a notice advising patrons that a copy of the most recent routine inspection report is available for review by interested parties. Keep a copy of the most recent health inspection report at the facility for customer review purposes.

Post and maintain a legible and conspicuous sign in each toilet room directing attention to the need to thoroughly wash hands after using the toilet.

Post and maintain a legible "No Smoking" sign in food preparation, food storage, and utensil washing areas.

 Observed lack of knowledge of the location of a copy of the most recent health inspection at the facility location. Maintain a copy of the most recent health inspection at the facility location, and ensure that employees are aware of its whereabouts and can provide a copy for customer inspection during all hours of operation. A new copy of most recent inspection report is being provided to the facility on this date. Corrected during inspection. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
4-19-2024 All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182) 1.00 Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.

Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.

The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated. 		1. Observed that soda machine had buildup of soda grime on the stems. Increase frequency and efficacy of cleaning of this machine. All equipment shall be cleaned and well maintained. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
4-19-2024 The premises of each food facility shall be kept clean and free of litter and rubbish; all clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept free of vermin. (114067 (j), 114123, 114143 (a) & (b), 114175, 114178, 114185, 114185.1, 114185.2, 114185.3, 114185.4, 114256, 114256.1, 114256.2, 114256.4, 114257, 114257.1, 114259, 114259.1, 114259.2, 114259.3, 114279, 114281, 114282) 1.00 All food facilities shall be kept clean, fully operative, and in good repair. A food facility shall at all times be so constructed, equipped, maintained, and operated as to prevent the entrance and harborage of animals, birds, and vermin, including, but not limited to, rodents and insects. The premises of each food facility shall be kept clean and free of litter, rubbish, and vermin.

Lockers or other suitable facilities shall be provided and used for the orderly storage of employee clothing and other possessions. Lockers or other suitable facilities shall be located in a designated room or area where contamination of food, equipment, utensils, linens, and single-use articles cannot occur. Dressing rooms or dressing areas shall be provided and used by employees if the employees regularly change their clothes in the facility. 		Observed that the door in thhe kitchen leading to the garbage and parking lot outside of the facility was left open after the food truck had left. Keep this door closed between deliveries or install a 16 mesh screen door to keep restaurant sealed while door is left open for ventilation. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
4-19-2024 The potable water supply shall be protected with a backflow or back siphonage protection device, as required by applicable plumbing codes. (114192) All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose. (114171, 114189.1, 114190, 114192.1, 114193, 114193.1, 114195, 114197, 114199, 114201, 114269) 1.00 All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Observed that drain from soda machine inside dining area went directly into floor sink. Provide 1 inch air gap above the rim of floor sink to provide backflow prevention. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
4-19-2024 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 2.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method. 		2nd Repeat: Observed the first compartment of the three compartment sink still not able to hold water. Repair/replace the sink stopper so it can hold water for proper dish washing. a 3rd repeat may result in further administrative action including an office hearing. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
4-19-2024 Handwashing soap and single use towels or drying device shall be provided in dispensers adjacent to each handwashing facility; dispensers shall be maintained in good repair. (113953.2) Adequate separate facilities shall be provided for handwashing, food preparation, and the washing of utensils and equipment. (113953, 113953.1) 3.00 Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees. Employees shall not clean their hands in a sink used for food preparation, warewashing, or in a service sink or a curbed cleaning facility used for the disposal of mop water and similar liquid waste. Do not place objects in front of the handwashing station, and do not place items, utensils or wiping cloths in the handwashing sink.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Soap shall be provided in approved dispensers at, or adjacent to, handwashing facilities (no bars of soap). Single-use sanitary towels or hot-air blowers shall be provided at handwashing facilities in approved dispensing devices. 		Observed lack of paper towels in a functioning paper towel dispenser or a functioning air hand drying unit adjacent to the hand washing sink. Provide a functioning paper towel dispenser adjacent to the handwashing sink and keep paper towel dispensers properly filled, or an air hand drying unit functional, to provide a sanitary method for hand drying at all times. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
4-19-2024 All food contact surfaces of utensils and equipment shall be clean and sanitized. (113984(e), 114097, 114099.1, 114099.4, 114099.6, 114101 (b-d), 114105, 114109, 114111, 114113, 114115 (a, b, d), 114117, 114125(b), 114135, 114141) 3.00 A food facility that prepares food shall not be operating if there is no method to properly clean and sanitize equipment or utensils. A food facility shall not be operating if there is gross contamination of food contact surfaces that may result in the contamination of food products. 1. Observed that buckets used for food storage were being stored right side up allowing for sanitizer ti remain in bucket instead of adequately drain. Ensure all equipment is air dried in a way that provides adequate drainage to prevent accidental cross contamination of sanitizer into food.
2. Observed 3 compartment sink was blocked and being used to prep chicken. No written procedure was available. provide a posted written procedure at 3-comp if you continue this practice. Procedure should note that the sink will be washed rinsed and sanitized before and after prep to prevent cross contamination. 		0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)


Rating on date 11-01-2021: Satisfactory (Total Points: 10.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
11-01-2021 No violations were noted during this inspection. 0.00 This food facility currently meets California Retail Food Code requirements, and is authorized by the Merced County Division of Environmental Health to be open for business. The permit is issued to the current business owner of record and is non-transferable. No violations noted for the commissary. 0145 COMMISSARY / OPEN FOOD PREP ALLOWED
11-01-2021 Wiping cloths used to wipe service counters, scales or other surfaces that may come into contact with food shall be used only once unless kept in clean water with sanitizer. (114135, 114185, 114185.1, 11485.2, 114185.3) 1.00 Cloths used to wipe service counters, scales, and other surfaces that may directly or indirectly contact food shall be used only once until laundered or may be used repeatedly if held in a sanitizing solution, as described below. Cloths used with raw foods of animal origin shall be used only once until laundered or may be used repeatedly if kept in a separate container of sanitizing solution, as described below:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with the manufacturer's use directions. 		Observed numerous wiping cloths left on the counters throughout the facility. Keep all wiping cloths in sanitizer solution if using more than once and not in use. Towels were either discarded or moved to a sanitizer solution during the inspection. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
11-01-2021 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 2.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method. 		(REPEAT VIOLATION) Observed the first compartment of the three compartment sink still not able to hold water. Repair/replace the sink stopper so it can hold water for proper dish washing. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
11-01-2021 Potentially hazardous foods shall be held at or below 41°/ 45°F or at or above 135°F. (113996, 113998, 114037, 114343(a)) 7.00 Hold potentially hazardous foods either at or above 135°F or at or below 41°F. Hold the following potentially hazardous foods at 45°F: raw shell eggs, unshucked live molluscan shellfish, pasteurized milk and pasteurized milk products in original, sealed containers. Potentially hazardous foods held for dispensing in a serving line or a salad bar (not in a display case) may be held at 45°F or less during periods not to exceed 12 hours in any 24-hour period. Discard all potentially hazardous food that has been out of an approved time and temperature range. Observed the walk-in fridge unit was measured at 45F during the inspection. Thermostat was adjusted and temperature dropped to 41F. Keep all potentially hazardous food items at 41F. Corrected during the inspection. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)


Rating on date 9-27-2021: Unsatisfactory - reinspection required (Total Points: 21.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
9-27-2021 No violations were noted during this inspection. 0.00 This food facility currently meets California Retail Food Code requirements, and is authorized by the Merced County Division of Environmental Health to be open for business. The permit is issued to the current business owner of record and is non-transferable. No violations noted for the commissary. 0145 COMMISSARY / OPEN FOOD PREP ALLOWED
9-27-2021 All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182) 1.00 Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.

Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.

The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated. 		(REPEAT VIOLATION) Observed the wooden shelves inside the walk-in freezer were made from raw, untreated wood. Paint/seal raw wood so it is smooth, easily cleanable, and nonabsorbent. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
9-27-2021 Each food facility shall be kept free of live animals and vermin: rodents (rats, mice), cockroaches, flies.( 114259.1, 114259.4, 114259.5) 3.00 Live animals are not allowed in a food facility, except as specified in section 114259.5.

A food facility shall immediately cease operation when there is a vermin infestation that has resulted in the contamination of food contact surfaces, food packaging, utensils, food equipment, or adulteration of food(s). The food facility shall remain closed until:
(a) there is no longer evidence of a vermin infestation.
(b) all contaminated surfaces have been cleaned and sanitized.
(c) contributing factors such as cleaning, repairs, and the elimination of harborages have been resolved.

All contributing factors must be resolved as quickly as possible. If there is a vermin infestation that warrants a major violation, then the permit to operate may be suspended. Professional pest control may also be required as frequently as needed to prevent the infestation from recurring. 		Observed numerous live baby flies in the back area near the soda syrup and dry storage area. Eradicate and sanitize all surfaces. Seek professional pest control if there is an extensive fly issue. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
9-27-2021 Wiping cloths used to wipe service counters, scales or other surfaces that may come into contact with food shall be used only once unless kept in clean water with sanitizer. (114135, 114185, 114185.1, 11485.2, 114185.3) 1.00 Cloths used to wipe service counters, scales, and other surfaces that may directly or indirectly contact food shall be used only once until laundered or may be used repeatedly if held in a sanitizing solution, as described below. Cloths used with raw foods of animal origin shall be used only once until laundered or may be used repeatedly if kept in a separate container of sanitizing solution, as described below:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with the manufacturer's use directions. 		Observed the sanitizer solution used to store wiping cloths was measured above 200PPM. Solution shall be at 100PPM. Use test strips to verify. Employees were educated on proper usage and a new sanitizer solution was made. Corrected during the inspection. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
9-27-2021 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 1.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method. 		Observed the sink stoppers at the three compartment sink were not functional. Repair/replace to provide for proper utensil washing. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
9-27-2021 Exhaust hoods shall be provided to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6" beyond all cooking equipment. All areas shall have sufficient ventilation to facilitate proper food storage. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. (114149, 114149.1) Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields. (114149.2, 114149.3, 114252, 114252.1) 1.00 All areas shall have sufficient ventilation to facilitate proper food storage and to provide a reasonable condition of comfort for each employee, consistent with the job performed by the employee.

Light fixtures in areas where food is prepared, open food is stored, or utensils are cleaned shall be of shatterproof construction or shall be protected with shatterproof shields and shall be readily cleanable. In every room and area in which any food is prepared, manufactured, processed, or prepackaged, or in which equipment or utensils are cleaned, sufficient natural or artificial lighting shall be provided to produce the following light intensity, while the area is in use:
(a) At least 10-foot candles for the following:
(1) At a distance of 30 inches above the floor, in walk-in refrigeration units, and dry food storage areas.
(2) At a working surface on which alcoholic beverages are prepared or where utensils used in the preparation or service of alcoholic beverages are cleaned.
(3) Inside equipment, such as reach-in or under-the-counter refrigerators.
(b) At least 20-foot candles for the following:
(1) At a surface where food is provided for consumer self-service or where fresh produce or prepackaged foods are sold or offered for consumption.
(2) In server stations where food is prepared.
(3) At a distance of 30 inches above the floor in areas used for handwashing, warewashing, and equipment and utensil storage, and in toilet rooms.
(c) Except in server stations where food is prepared, at least 50-foot candles at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor. 		Observed the lack of lighting inside the walk-in freezer. Repair/replace to provide adequate lighting for cleaning and safety reasons. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
9-27-2021 All food employees shall have adequate knowledge of and be trained in food safety as it relates to their assigned duties. The person in charge shall have adequate knowledge of, and shall educate employees of the food facility regarding major food allergens. (113947) Food facilities that prepare, handle or serve non-prepackaged potentially hazardous food, shall have an employee who has passed an approved food safety certification examination. (113947-113947.1) 3.00 The responsibilities of the staff member certified in food safety include ensuring that all employees who handle, or have responsibility for handling, unpackaged foods of any kind have sufficient knowledge to ensure the safe preparation and /or service of the food. The nature and extent of the knowledge that each employee is required to have may be tailored, as appropriate, to the employee's duties related to food safety issues. Observed the lack of proof that all employees have a certified food handler certificate. Provide proof and keep a copy of the certificate at the facility. All employees shall have one in 30 days. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
9-27-2021 All nonfood contact surfaces of utensils and equipment shall be clean. (114115, 114130.4) 1.00 Clean nonfood contact surfaces of equipment at a frequency necessary to prevent accumulation of residue. Observed the build up of dust on the fan units inside both restrooms. Clean and increase frequency to prevent build up. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
9-27-2021 Handwashing soap and single use towels or drying device shall be provided in dispensers adjacent to each handwashing facility; dispensers shall be maintained in good repair. (113953.2) Adequate separate facilities shall be provided for handwashing, food preparation, and the washing of utensils and equipment. (113953, 113953.1) 3.00 Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees. Employees shall not clean their hands in a sink used for food preparation, warewashing, or in a service sink or a curbed cleaning facility used for the disposal of mop water and similar liquid waste. Do not place objects in front of the handwashing station, and do not place items, utensils or wiping cloths in the handwashing sink.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Soap shall be provided in approved dispensers at, or adjacent to, handwashing facilities (no bars of soap). Single-use sanitary towels or hot-air blowers shall be provided at handwashing facilities in approved dispensing devices. 		Observed the lack of hot water at the hand wash sink in the back food prep area. Repair/replace so there is hot water at a minimum of 100F for proper hand washing. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
9-27-2021 Potentially hazardous foods shall be held at or below 41°/ 45°F or at or above 135°F. (113996, 113998, 114037, 114343(a)) 7.00 Hold potentially hazardous foods either at or above 135°F or at or below 41°F. Hold the following potentially hazardous foods at 45°F: raw shell eggs, unshucked live molluscan shellfish, pasteurized milk and pasteurized milk products in original, sealed containers. Potentially hazardous foods held for dispensing in a serving line or a salad bar (not in a display case) may be held at 45°F or less during periods not to exceed 12 hours in any 24-hour period. Discard all potentially hazardous food that has been out of an approved time and temperature range. Observed the temperature inside the walk-in fridge unit was measured at 43F during the inspection. Have the unit evaluated and repaired as necessary so the temperature is at 41F and under. Keep all potentially hazardous food items at 41F and under. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)