Return To Restaurant Listing | Return to Environmental Health Homepage

Facility: Subway
Address: 495 Fifth St. Ste A, Gustine, CA

The most recent inspection of this food facility resulted in a rating of
Good (Total Points: 6.00)
0-6  Points: Good
7-13 Points: Satisfactory
14+  Points: Unsatisfactory
Rating on date 2-05-2019: Good (Total Points: 6.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
2-05-2019 All nonfood contact surfaces of utensils and equipment shall be clean. (114115, 114130.4) 2.00 Clean nonfood contact surfaces of equipment at a frequency necessary to prevent accumulation of residue. Observed dirt, grime, and / or syrup residue buildup behind and between soda nozzle heads. Also observed residue buildup on the floor in the back room beneath the soda syrup rack. Improve cleaning frequency and methods to ensure all equipment is kept in an appropriate state of cleanliness; ensure all equipment surfaces are smooth and easily cleanable, and all potential food contact surfaces are sanitized on a regular basis. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
2-05-2019 An adequate, protected, pressurized, potable supply of hot water and cold water shall be provided at all times. (113953(c), 114099.2(b) 114101(a), 114189, 114192, 114192.1, 114195) 4.00 Provide hot and cold water under pressure through a mixing valve to each sink compartment. The water supply shall be from a water system approved by the health officer or the state department. An adequate, protected, pressurized, potable supply of hot water, at least 120°F, and cold water shall be provided.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees
REPEAT: Observed water temperatures at three comp, janitorial, and prep sinks are 111-114ºF. Adjust or repair so as to provide water to each of these sink locations consistently at not less than 120ºF.

Provide hot and cold water under pressure through a mixing valve to each sink compartment. Hot water shall be at least 120ºF. Warm tempered water may be substituted for hot and cold water at handwashing sinks only (100-108ºF).
0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)


Rating on date 11-01-2017: Good (Total Points: 4.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
11-01-2017 An adequate, protected, pressurized, potable supply of hot water and cold water shall be provided at all times. (113953(c), 114099.2(b) 114101(a), 114189, 114192, 114192.1, 114195) 2.00 Provide hot and cold water under pressure through a mixing valve to each sink compartment. The water supply shall be from a water system approved by the health officer or the state department. An adequate, protected, pressurized, potable supply of hot water, at least 120°F, and cold water shall be provided.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees
Observed water temperatures at three comp, janitorial, and prep sinks are 110-113ºF. Adjust or repair. Provide hot and cold water under pressure through a mixing valve to each sink compartment. Hot water shall be at least 120ºF. Warm tempered water may be substituted for hot and cold water at handwashing sinks. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
11-01-2017 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 2.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method.
Observed initial reading on quat sanitizer was ~50 ppm. Air bubbles discovered in concentrate feed line, worked bubbles out, re-dispensed sanitizer, now measuring ~200 ppm. Increase testing frequency for sanitizer to ensure equipment is dispensing solution at the correct strength. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)