Return To Restaurant Listing | Return to Environmental Health Homepage

Facility: Josie's Lounge & Restaurant
Address: 1301 Commerce Ave., Atwater, CA

The most recent inspection of this food facility resulted in a rating of
Satisfactory (Total Points: 8.00)
0-6  Points: Good
7-13 Points: Satisfactory
14+  Points: Unsatisfactory
Rating on date 2-01-2019: Satisfactory (Total Points: 8.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
2-01-2019 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 4.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method.
(REPEAT VIOLATION)(CDI) Observed the dish washing machine is not working properly and not dispensing sanitizer solution. Machine shall dispense 50PPM of chlorine for proper dish washing. Violation was corrected during inspection. Dish washing machine was able to dispense 50PPM of chlorine during inspection.

Observed employee washing utensils at the one compartment sink. This sink is only supposed to be used for food prep only. Wash all utensils at the three compartment sink or run through the dishwasher.
0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
2-01-2019 Food employees shall keep their hands and exposed portions of their arms clean, and shall maaintain fingernails so they are cleanable. Employees are required to wash their hands: before beginning work; before handling food / equipment / utensils; as often as necessary during food preparation to remove soil and contamination; when switching from working with raw to ready-to-eat foods; after touching body parts; after using the toilet room; or any time when contamination may occur. (113952, 113953.3, 113968, 113973 (b-f)). Whenever gloves are worn, they shall be changed as often as handwashing is required. 0.00 The food employee shall wash their hands and portion of arms as required, and use utensils and gloves appropriately. Be sure employees are washing their hands at the hand wash sink, and drying with paper towels. Do not use cloth towels to dry hands. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
2-01-2019 All nonfood contact surfaces of utensils and equipment shall be clean. (114115, 114130.4) 4.00 Clean nonfood contact surfaces of equipment at a frequency necessary to prevent accumulation of residue. (REPEAT VIOLATION) Observed the build up of spilled beer and other drink mixes inside the fridge units holding the kegs at the bar area. Clean and increase frequency to prevent build up. 0123 BAR


Rating on date 12-27-2018: Unsatisfactory - reinspection required (Total Points: 27.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
12-27-2018 All nonfood contact surfaces of utensils and equipment shall be clean. (114115, 114130.4) 2.00 Clean nonfood contact surfaces of equipment at a frequency necessary to prevent accumulation of residue. Observed the build up of spilled beer and other drink mixes inside the fridge units at the bar area. Clean and increase frequency to prevent build up. 0123 BAR
12-27-2018 The potable water supply shall be protected with a backflow or back siphonage protection device, as required by applicable plumbing codes. (114192) All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose. (114171, 114189.1, 114190, 114192.1, 114193, 114193.1, 114195, 114197, 114199, 114201, 114269) 2.00 All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Observed the drain lines from the refrigeration units lacking a minimum one inch air gap between the floor drain and the drain lines. Repair so there is a one inch minimum air gap. 0123 BAR
12-27-2018 Handwashing soap and single use towels or drying device shall be provided in dispensers adjacent to each handwashing facility; dispensers shall be maintained in good repair. (113953.2) Adequate separate facilities shall be provided for handwashing, food preparation, and the washing of utensils and equipment. (113953, 113953.1) 0.00 Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees. Employees shall not clean their hands in a sink used for food preparation, warewashing, or in a service sink or a curbed cleaning facility used for the disposal of mop water and similar liquid waste. Do not place objects in front of the handwashing station, and do not place items, utensils or wiping cloths in the handwashing sink.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Soap shall be provided in approved dispensers at, or adjacent to, handwashing facilities (no bars of soap). Single-use sanitary towels or hot-air blowers shall be provided at handwashing facilities in approved dispensing devices.
Observed the lack of paper towels in mounted dispenser. Provide paper towels in mounted dispenser at all times for proper hand washing. 0123 BAR
12-27-2018 Toilet facilities shall be maintained clean, sanitary and in good repair. Toilet rooms shall be separated by a well-fitting self-closing door. Toilet tissue shall be provided in a permanently installed dispenser at each toilet. The number of toilet facilities shall be in accordance with local building and plumbing ordinances. Toilet facilities shall be provided for patrons: in establishments with more than 20,000 sq ft.; establishments offering on-site food consumption. (113953, 113953.1, 113953.2, 114250, 114250.1, 114276) 2.00 Provide clean toilet facilities in good repair. Provide permanently installed toilet tissue dispenser(s) in all toilet facilities. Provide handwashing facilities within or adjacent to all toilet facilities. Soap shall be provided in dispensers at, or adjacent to, handwashing facilities. Single-use sanitary towels in dispensers or hot-air blowers shall be provided at handwashing facilities.

Customer restrooms are required for food facilities of more than 20,000 square feet if they were constructed after July 1 1984, and also applies to facilities of any size that were constructed after January 1, 2004 where there is onsite consumption of food. A "take-out only" food facility, with no seating indoors or outdoors, may not be required to provide customer restrooms. Check with the Division of Environmental Health and with the appropriate Planning Department before removing or restricting access to customer restrooms.
Observed the hand wash temperature at the mens restroom is only reaching 67F. Water at the hand wash sink shall reach a minimum of 100F for proper hand washing. Repair.

Observed the lack of notice to remind employees to wash their hands after visiting the restroom. Provide a notice to remind employees.
0123 BAR
12-27-2018 All nonfood contact surfaces of utensils and equipment shall be clean. (114115, 114130.4) 0.00 Clean nonfood contact surfaces of equipment at a frequency necessary to prevent accumulation of residue. Observed the build up of dust on the fan blade covers inside the walk-in fridge unit. Clean and increase frequency to prevent build up.

Observed the build up of food debris and particles on the cooking equipment in the kitchen area. Clean and increase frequency to prevent build up.
0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
12-27-2018 Wiping cloths used to wipe service counters, scales or other surfaces that may come into contact with food shall be used only once unless kept in clean water with sanitizer. (114135, 11485, 114185.1, 11485.2, 114185.3) 4.00 Cloths used to wipe service counters, scales, and other surfaces that may directly or indirectly contact food shall be used only once until laundered or may be used repeatedly if held in a sanitizing solution, as described below. Cloths used with raw foods of animal origin shall be used only once until laundered or may be used repeatedly if kept in a separate container of sanitizing solution, as described below:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with the manufacturer's use directions.
(REPEAT VIOLATION) Observed the sanitizer solution used to store wiping cloths was measured above 200PPM. sanitizer solution shall be at 100PPM. Be sure to use test strips to measure solution and make sure it is at correct PPM. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
12-27-2018 All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182) 2.00 Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.

Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.

The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated.
Observed a cutting board sitting directly over the flat top grill being used to stabilize the oven unit above. Remove cutting board as it has been warped and is a potential contamination issue. Repair oven as necessary so it does not fall. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
12-27-2018 All potentially hazardous food shall be RAPIDLY cooled from 135°F to 70°F, within 2 hours, and then from 70°F to 41°F, within 4 hours. Cooling shall be by one or more of the methods outlined below. (114002, 114002.1) 0.00 Destroy all contaminated food. All potentially hazardous food must be rapidly cooled within the following time frames: from 135°F to 41°F or below within 6 hours and, during this time the decrease in temperature from 135°F to 70°F shall occur within the first 2 hours. Potentially hazardous food prepared from ingredients at ambient temperature shall be cooled within 4 hours to 41°F or less.

The rapid cooling of potentially hazardous foods shall be accomplished in accordance with the time and temperature criteria specified above by using one or more of the following methods based on the type of food being cooled:
(1) Placing the food in shallow pans.
(2) Separating the food into smaller or thinner portions.
(3) Using rapid cooling equipment .
(4) Using containers that facilitate heat transfer.
(5) Adding ice as an ingredient.
(6) Using ice paddles.
(7) Inserting appropriately designed containers in an ice bath and stirring frequently.
(8) In accordance with an approved HACCP plan or by other means that have been approved by the Division of Environmental Health.
Observed a large bucket of pinto beans being stored inside the walk-in fridge that measured at 57F at the center of the beans. Beans were discarded during inspection. Operator stated beans were made the previous day. Operator was instructed on the correct method to properly cool and store beans. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
12-27-2018 All food shall be separated and protected from contamination. (113984, 113986, 113988, 113990, 114060, 114067, 114069, 114077, 114079, 114089.1 (c), 114143 (c)) 0.00 Destroy all contaminated food. All food shall be prepared, stored, displayed, dispensed, placed, transported, sold, and served as to be protected from dirt, vermin, unnecessary handling, droplet contamination, overhead leakage, or other contamination.
If unpackaged food is displayed and sold in bulk in other than self-service containers, then it shall be served by an employee of the food establishment directly to a consumer and shall be displayed in clean, sanitary, and covered or otherwise protected containers.
For bulk customer self-service food items, such as salad bars, buffet type foods, and other ready-to-eat food, install sneeze guards that intercept a direct line between the customer's mouth and the food being offered, dispense from approved mechanical dispensers, or employ other effective means to protect ready-to-eat food from contamination.
Protect all cartons, boxes, or other materials used in the packaging of any food from dirt, vermin, and other forms of contamination or adulteration.
Observed the lack of covers on the food items at the hot holding unit. Provide a lid on all food items when not under diligent preparation. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
12-27-2018 Handwashing soap and single use towels or drying device shall be provided in dispensers adjacent to each handwashing facility; dispensers shall be maintained in good repair. (113953.2) Adequate separate facilities shall be provided for handwashing, food preparation, and the washing of utensils and equipment. (113953, 113953.1) 4.00 Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees. Employees shall not clean their hands in a sink used for food preparation, warewashing, or in a service sink or a curbed cleaning facility used for the disposal of mop water and similar liquid waste. Do not place objects in front of the handwashing station, and do not place items, utensils or wiping cloths in the handwashing sink.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Soap shall be provided in approved dispensers at, or adjacent to, handwashing facilities (no bars of soap). Single-use sanitary towels or hot-air blowers shall be provided at handwashing facilities in approved dispensing devices.
(REPEAT VIOLATION) Observed the hand wash sink was blocked by a large bowl of tomatoes as employee was slicing them. Do not store anything inside or block access to the hand wash sink. This sink is only meant for hand washing and all hand washing shall be conducted at this sink. Sink was cleared during inspeciton. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
12-27-2018 Potentially hazardous foods shall be held at or below 41°/ 45°F or at or above 135°F. (113996, 113998, 114037, 114343(a)) 7.00 Hold potentially hazardous foods either at or above 135°F or at or below 41°F. Hold the following potentially hazardous foods at 45°F: raw shell eggs, unshucked live molluscan shellfish, pasteurized milk and pasteurized milk products in original, sealed containers. Potentially hazardous foods held for dispensing in a serving line or a salad bar (not in a display case) may be held at 45°F or less during periods not to exceed 12 hours in any 24-hour period. Discard all potentially hazardous food that has been out of an approved time and temperature range. Observed a large bucket of pinto beans being stored inside the walk-in fridge that measured at 57F at the center of the beans. Beans were discarded during inspection. Operator stated beans were made the previous day. Operator was instructed on the correct method to properly cool and store beans. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
12-27-2018 The walls / ceilings shall have durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair. (114065, 114067, 114069, 114175, 114143, 114257, 114259.2, 114266, 114268, 114268.1, 114271, 114272) 2.00 All food facilities shall be kept clean, fully operative, and in good repair. Floor surfaces in all areas in which food is prepared, packaged or stored, where any utensil is washed, where refuse or garbage is stored, where janitorial facilities are located, and in all restrooms and hand washing areas shall be smooth and of durable construction and made from non absorbent material that is easily cleanable.

Each permanent food facility shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. Food facilities that are not fully enclosed on all sides and that are in operation on January 1, 1985, shall not be required to meet the requirements of this section until the facility is remodeled or has a significant menu change or a change in its method of operation. Full enclosure is not required for dining areas and certain other areas when approved for outdoor food services.
Observed the build up of food debris and residue on the walls directly behind the cooking equipment. Clean and increase frequency to prevent build up. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
12-27-2018 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 2.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method.
Observed the dish washing machine is not working properly and not dispensing sanitizer solution. Machine shall dispense 50PPM of chlorine for proper dish washing. Facility must use three compartment method to wash dishes until machine is repaired and dispenses Chlorine. Sanitizer level for three compartment washing method shall be at 100PPM of Chlorine. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)


Rating on date 2-01-2018: Satisfactory (Total Points: 12.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
2-01-2018 No violations were noted during this inspection. 0.00 This food facility currently meets California Retail Food Code requirements, and is authorized by the Merced County Division of Environmental Health to be open for business. The permit is issued to the current business owner of record and is non-transferable. No violations noted during inspection see food establishment inspection. 0123 BAR
2-01-2018 Handwashing soap and single use towels or drying device shall be provided in dispensers adjacent to each handwashing facility; dispensers shall be maintained in good repair. (113953.2) Adequate separate facilities shall be provided for handwashing, food preparation, and the washing of utensils and equipment. (113953, 113953.1) 4.00 Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees. Employees shall not clean their hands in a sink used for food preparation, warewashing, or in a service sink or a curbed cleaning facility used for the disposal of mop water and similar liquid waste. Do not place objects in front of the handwashing station, and do not place items, utensils or wiping cloths in the handwashing sink.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Soap shall be provided in approved dispensers at, or adjacent to, handwashing facilities (no bars of soap). Single-use sanitary towels or hot-air blowers shall be provided at handwashing facilities in approved dispensing devices.
(CDI) Observed hand wash sink being blocked by bags of beans and employee had a bowl of jalepenos inside of hand wash sink. Keep hand wash sink clear and easily accessible at all times for handwashing only. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
2-01-2018 Wiping cloths used to wipe service counters, scales or other surfaces that may come into contact with food shall be used only once unless kept in clean water with sanitizer. (114135, 11485, 114185.1, 11485.2, 114185.3) 4.00 Cloths used to wipe service counters, scales, and other surfaces that may directly or indirectly contact food shall be used only once until laundered or may be used repeatedly if held in a sanitizing solution, as described below. Cloths used with raw foods of animal origin shall be used only once until laundered or may be used repeatedly if kept in a separate container of sanitizing solution, as described below:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with the manufacturer's use directions.
Observed the failure to maintain proper concentration of sanitizing solution used for cleaning cloths. Solution was measured above 200ppm. Solution needs to be between 50 to 100 ppm. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
2-01-2018 The potable water supply shall be protected with a backflow or back siphonage protection device, as required by applicable plumbing codes. (114192) All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose. (114171, 114189.1, 114190, 114192.1, 114193, 114193.1, 114195, 114197, 114199, 114201, 114269) 4.00 All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Observed lack of one inch minimum air gap between the drain lines under the three comp sink and food prep sink and the rim height of the floor sink. Repair or modify drain lines so that the distance between the lowest edge of the drain lines and the height of the floor sink rim allows for a minimum of a one inch air gap. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)


Rating on date 12-27-2017: Unsatisfactory - reinspection required (Total Points: 25.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
12-27-2017 Handwashing soap and single use towels or drying device shall be provided in dispensers adjacent to each handwashing facility; dispensers shall be maintained in good repair. (113953.2) Adequate separate facilities shall be provided for handwashing, food preparation, and the washing of utensils and equipment. (113953, 113953.1) 0.00 Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees. Employees shall not clean their hands in a sink used for food preparation, warewashing, or in a service sink or a curbed cleaning facility used for the disposal of mop water and similar liquid waste. Do not place objects in front of the handwashing station, and do not place items, utensils or wiping cloths in the handwashing sink.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Soap shall be provided in approved dispensers at, or adjacent to, handwashing facilities (no bars of soap). Single-use sanitary towels or hot-air blowers shall be provided at handwashing facilities in approved dispensing devices.
Observed lack of paper towels in a functioning paper towel dispenser or a functioning air hand drying unit adjacent to the hand washing sink in the bar area. Provide a functioning paper towel dispenser adjacent to the handwashing sink and keep paper towel dispensers properly filled, or an air hand drying unit functional, to provide a sanitary method for hand drying at all times. 0123 BAR
12-27-2017 All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182) 0.00 Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.

Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.

The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated.
Observed CO2 tanks in bar area under th counter that are not secured. Ensure all pressurized cylinders are securely fastened to a rigid structure.

Observed mildew on soda dispenser in bar area. Clean and sanitize and improve frequency of cleaning.

Observed bucket in beer reach in fridge that is collecting water from unit due to a leak. Fix or replace the unit so that it will no longer require the bucket to catch the water.
0123 BAR
12-27-2017 Exhaust hoods shall be provided to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6" beyond all cooking equipment. All areas shall have sufficient ventilation to facilitate proper food storage. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. (114149, 114149.1) Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields. (114149.2, 114149.3, 114252, 114252.1) 2.00 All areas shall have sufficient ventilation to facilitate proper food storage and to provide a reasonable condition of comfort for each employee, consistent with the job performed by the employee.

Light fixtures in areas where food is prepared, open food is stored, or utensils are cleaned shall be of shatterproof construction or shall be protected with shatterproof shields and shall be readily cleanable. In every room and area in which any food is prepared, manufactured, processed, or prepackaged, or in which equipment or utensils are cleaned, sufficient natural or artificial lighting shall be provided to produce the following light intensity, while the area is in use:
(a) At least 10-foot candles for the following:
(1) At a distance of 30 inches above the floor, in walk-in refrigeration units, and dry food storage areas.
(2) At a working surface on which alcoholic beverages are prepared or where utensils used in the preparation or service of alcoholic beverages are cleaned.
(3) Inside equipment, such as reach-in or under-the-counter refrigerators.
(b) At least 20-foot candles for the following:
(1) At a surface where food is provided for consumer self-service or where fresh produce or prepackaged foods are sold or offered for consumption.
(2) In server stations where food is prepared.
(3) At a distance of 30 inches above the floor in areas used for handwashing, warewashing, and equipment and utensil storage, and in toilet rooms.
(c) Except in server stations where food is prepared, at least 50-foot candles at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor.
Observed two light fixtures in the the exhaust hood system over fryer and grill that do not function, bulb may be burned out. Replace bulb and / or repair fixture. Failure to provide adequate lighting.

Observed missing/broken air filter in exhaust hood system. Repair or replace with appropriate filter.
0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
12-27-2017 All poisonous substances, detergents, bleaches, and cleaning compounds shall be properly labeled and stored separate from food, utensils, packing material, and food-contact surfaces. (114254, 114254.1, 114254.2) 7.00 All poisonous substances, detergents, bleaches, cleaning compounds, and all other injurious or poisonous materials shall be stored and used only in a manner that is not likely to cause contamination or adulteration of food, food contact surfaces, utensils, or packaging materials. Poisonous or toxic materials shall be stored or displayed so they cannot contaminate food, equipment, utensils, linens, and single-use articles by separating the poisonous or toxic materials by spacing or partitioning and locating the poisonous or toxic materials in an area that is not above food, equipment, utensils, linens, and single-use articles. Equipment and utensil cleaners and sanitizers may be stored in warewashing areas for availability and convenience if the materials are stored to prevent contamination of food, equipment, utensils, linens, and single-use articles.

Containers of poisonous or toxic materials and personal care items shall bear a legible manufacturer's label. Working containers used for storing poisonous or toxic materials such as cleaners and sanitizers taken from bulk supplies shall be clearly and individually identified with the common name of the material. A container previously used to store poisonous or toxic materials shall not be used to store, transport, or dispense food, utensils, and linen.

Only those insecticides, rodenticides and other pesticides that are specifically approved for use in a food facility may be used. The use shall be in accordance with manufacturer's instructions.
Observed AJAX located in dishwashing area next to and above utensils which may result in potential contamination of food products or food prep surfaces. Relocate all chemicals/ non food items so that they are stored in a distinctly separate area below and away from all food products and food prep surfaces, in such a way so as to eliminate potential contamination. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
12-27-2017 Potentially hazardous foods shall be held at or below 41°/ 45°F or at or above 135°F. (113996, 113998, 114037, 114343(a)) 2.00 Hold potentially hazardous foods either at or above 135°F or at or below 41°F. Hold the following potentially hazardous foods at 45°F: raw shell eggs, unshucked live molluscan shellfish, pasteurized milk and pasteurized milk products in original, sealed containers. Potentially hazardous foods held for dispensing in a serving line or a salad bar (not in a display case) may be held at 45°F or less during periods not to exceed 12 hours in any 24-hour period. Discard all potentially hazardous food that has been out of an approved time and temperature range. Observed the temperature of the chopped chicken that was measured between 45-50 °F at the refrigerator unit under the stove. Keep all cold potentially hazardous foods at or below 41°F. Adjust and / or repair this unit; do not use it for the storage of PHF (potentially hazardous food) items until it is shown to consistently capable of holding food at or below 41ºF at all times.
Note: (Employee states that chicken was chopped 30 minutes prior).
0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
12-27-2017 The potable water supply shall be protected with a backflow or back siphonage protection device, as required by applicable plumbing codes. (114192) All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose. (114171, 114189.1, 114190, 114192.1, 114193, 114193.1, 114195, 114197, 114199, 114201, 114269) 2.00 All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Observed lack of one inch air gap between the drain lines coming from the dishwasher and three compartment sink and the rim height of the floor sink. Repair or modify drain lines so that the distance between the lowest edge of the drain lines and the height of the floor sink rim allows for a minimum of a one inch air gap.

Observed drain line from two compartment sink that is draining onto floor and not into floor drain. Adjust or add an extra piece of pipe to allow draining into floor drain.
0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
12-27-2017 All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182) 4.00 Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.

Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.

The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated.
Observed small CO2 tank near soda syrup boxes that are not secured. Ensure all pressurized cylinders are securely fastened to a rigid structure.

Observed the cutting board at food prep fridge is grooved and discolored, does not appear to come completely clean, and no longer constitutes a smooth and easily cleanable surface. Repair or replace damaged and discolored cutting boards; ensure that all food / utensil contact surfaces are smooth, easily cleanable, and nonporous.

Observed the wall mounted slicer press near handwash sink with accumulated debris on the backing attached. Improve cleaning frequency and methods to ensure all equipment is kept in an appropriate state of cleanliness.

Observed dirt, grime, and / or food particle buildup on the storage rack inside the food prep fridge. Improve cleaning frequency and methods to ensure all equipment is kept in an appropriate state of cleanliness; ensure all equipment surfaces are smooth and easily cleanable, and all potential food contact surfaces are sanitized on a regular basis.

Observed build up and potential mold growth on inside white plastic plate in ice machine. Improve cleaning frequency and methods to ensure all equipment is kept in an appropriate state of cleanliness; ensure all equipment surfaces are smooth and easily cleanable, and all potential food contact surfaces are sanitized on a regular basis.

Observed build up of food debris on outside of Ice machine. Improve cleaning frequency and methods to ensure all equipment is kept in an appropriate state of cleanliness.

Observed food prep sink that is coming detached from wall and lacking sealant. Repair so that sink is reattached to wall and provides a smooth and easily cleanable surface.

Observed build up of dust debris on fan blade guards on cooler unit in walk-in refrigerator and/or freezer. Improve cleaning frequency to prevent a visible buildup of dust debris.

Observed Food build/splatter on wall behind stoves and grills. Improve cleaning frequency and methods to ensure all equipment is kept in an appropriate state of cleanliness.
0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
12-27-2017 All food employees shall have adequate knowledge of and be trained in food safety as it relates to their assigned duties. The person in charge shall have adequate knowledge of, and shall educate employees of the food facility regarding major food allergens. (113947) Food facilities that prepare, handle or serve non-prepackaged potentially hazardous food, shall have an employee who has passed an approved food safety certification examination. (113947-113947.1) 2.00 The responsibilities of the staff member certified in food safety include ensuring that all employees who handle, or have responsibility for handling, unpackaged foods of any kind have sufficient knowledge to ensure the safe preparation and /or service of the food. The nature and extent of the knowledge that each employee is required to have may be tailored, as appropriate, to the employee's duties related to food safety issues. (CDI) Observed the lack of knowledge by an employee on proper methods to clean and sanitize dishes manually. All food employees shall have adequate knowledge of and be trained in food safety as it relates to their assigned duties. Proper methods on how to wash, rinse, and sanitize were taught to employees.

Observed lack of proof that a current employee of this establishment holds a Food Safety Manager Class certificate that is no more than five years old. Maintain a copy of the original certificate for at least one current employee at the facility location. The food managers certificate that is earned by the employee or owner may be used at only one location. Obtain a certificate from an American National Standards Institute approved food handling/food safety examination; if no one holds a current food safety certificate, obtain one within 60 days.
0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
12-27-2017 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 2.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method.
Observed lack of sanitizer of sufficient strength in dishwashing machine. Instructed employees in manual sanitizing techniques. Perform manual sanitation of all dishes at this location at 100 ppm (parts per million). Use the correct test strips for the chemical sanitizer being used. Check the sanitizer strength at a sufficient frequency to ensure consistent sanitation of all food contact surfaces in this location. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
12-27-2017 Handwashing soap and single use towels or drying device shall be provided in dispensers adjacent to each handwashing facility; dispensers shall be maintained in good repair. (113953.2) Adequate separate facilities shall be provided for handwashing, food preparation, and the washing of utensils and equipment. (113953, 113953.1) 2.00 Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees. Employees shall not clean their hands in a sink used for food preparation, warewashing, or in a service sink or a curbed cleaning facility used for the disposal of mop water and similar liquid waste. Do not place objects in front of the handwashing station, and do not place items, utensils or wiping cloths in the handwashing sink.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Soap shall be provided in approved dispensers at, or adjacent to, handwashing facilities (no bars of soap). Single-use sanitary towels or hot-air blowers shall be provided at handwashing facilities in approved dispensing devices.
(CDI) Observed lack of soap in the approved dispenser at the handwashing sink in the dishwashing area. Keep an approved soap dispenser filled and functional at all times for handwashing purposes.

Observed the failure to provide adequate access to handwashing facilities in a food preparation area.
Note: Handwash sink should only be used to wash hands do not pour out beverages and ice into sink.
0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
12-27-2017 The premises of each food facility shall be kept clean and free of litter and rubbish; all clean and soiled linen shall be properly stored; non-food items shall be stored and displayed separate from food and food-contact surfaces; the facility shall be kept free of vermin. (114067 (j), 114123, 114143 (a) & (b), 114175, 114178, 114185, 114185.1, 114185.2, 114185.3, 114185.4, 114256, 114256.1, 114256.2, 114256.4, 114257, 114257.1, 114259, 114259.1, 114259.2, 114259.3, 114279, 114281, 114282) 2.00 All food facilities shall be kept clean, fully operative, and in good repair. A food facility shall at all times be so constructed, equipped, maintained, and operated as to prevent the entrance and harborage of animals, birds, and vermin, including, but not limited to, rodents and insects. The premises of each food facility shall be kept clean and free of litter, rubbish, and vermin.

Lockers or other suitable facilities shall be provided and used for the orderly storage of employee clothing and other possessions. Lockers or other suitable facilities shall be located in a designated room or area where contamination of food, equipment, utensils, linens, and single-use articles cannot occur. Dressing rooms or dressing areas shall be provided and used by employees if the employees regularly change their clothes in the facility.
Observed employee belongings intermingling with food items. Lockers or other suitable facilities shall be provided and used for the orderly storage of employee clothing and other possessions. Lockers or other suitable facilities shall be located in a designated room or area where contamination of food, equipment, utensils, linens, and single-use articles cannot occur. 0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)