2-09-2021 |
Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125)
| 1.00 |
Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.
Clean the utensils in one of the following ways:
(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following: (a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above. (b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions: (1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds. (2) Contact with a solution of 25 ppm available iodine for at least one minute. (3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute. (4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6. (c) Other methods approved by the enforcement agency.
(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following: (a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above. (b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following: (1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds. (2) Contact with a solution of 25 ppm available iodine for at least one minute. (3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.
Provide testing equipment and materials to adequately measure the applicable sanitization method.
|
Observed lack of test strips to measure the applicable manual sanitizer concentration. Obtain and use test strips to verify sanitizer is of sufficient strength to act as an appropriate manual sanitizing agent (100 ppm for chlorine, 200 ppm for quat ammonia).
|
0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
|
2-09-2021 |
All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182)
| 1.00 |
Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.
Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.
The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated.
|
Observed the use of cardboard to catch grease. Replace with a tray or equipment with a smooth and easily cleanable surface.
|
0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
|
2-09-2021 |
All food shall be separated and protected from contamination. (113984, 113986, 113988, 113990, 114060, 114067, 114069, 114077, 114079, 114089.1 (c), 114143 (c))
| 1.00 |
Destroy all contaminated food. All food shall be prepared, stored, displayed, dispensed, placed, transported, sold, and served as to be protected from dirt, vermin, unnecessary handling, droplet contamination, overhead leakage, or other contamination. If unpackaged food is displayed and sold in bulk in other than self-service containers, then it shall be served by an employee of the food establishment directly to a consumer and shall be displayed in clean, sanitary, and covered or otherwise protected containers. For bulk customer self-service food items, such as salad bars, buffet type foods, and other ready-to-eat food, install sneeze guards that intercept a direct line between the customer's mouth and the food being offered, dispense from approved mechanical dispensers, or employ other effective means to protect ready-to-eat food from contamination. Protect all cartons, boxes, or other materials used in the packaging of any food from dirt, vermin, and other forms of contamination or adulteration.
|
Observed a few food items not covered in the refrigerators. Keep covered when not in use.
|
0101 FOOD ESTAB. W/FOOD PREP 0-49 SEATS (HM4)
|