Return To Restaurant Listing | Return to Environmental Health Homepage

Facility: Round Table Pizza
Address: 1831 Bellevue Road, Atwater, CA

The most recent inspection of this food facility resulted in a rating of
Unsatisfactory (Total Points: 24.00)
0-6  Points: Good
7-13 Points: Satisfactory
14+  Points: Unsatisfactory
Rating on date 2-20-2020: Unsatisfactory - reinspection required (Total Points: 24.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
2-20-2020 The potable water supply shall be protected with a backflow or back siphonage protection device, as required by applicable plumbing codes. (114192) All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose. (114171, 114189.1, 114190, 114192.1, 114193, 114193.1, 114195, 114197, 114199, 114201, 114269) 3.00 All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Observed the floor sink in the back under the dish washing machine and three compartment sink is no properly draining. The dishwasher is unable to be used because the floor sink does not drain fast enough. When dish washer is ran or three compartment sink is drained, the floor sink overflows onto the floor. Have the floor sink repaired/replaced immediately within 14 days(March 6, 2020). If it is not fixed within the 14 days facility will not be allowed to operate until it is repaired. 0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
2-20-2020 All food shall be separated and protected from contamination. (113984, 113986, 113988, 113990, 114060, 114067, 114069, 114077, 114079, 114089.1 (c), 114143 (c)) 1.00 Destroy all contaminated food. All food shall be prepared, stored, displayed, dispensed, placed, transported, sold, and served as to be protected from dirt, vermin, unnecessary handling, droplet contamination, overhead leakage, or other contamination.
If unpackaged food is displayed and sold in bulk in other than self-service containers, then it shall be served by an employee of the food establishment directly to a consumer and shall be displayed in clean, sanitary, and covered or otherwise protected containers.
For bulk customer self-service food items, such as salad bars, buffet type foods, and other ready-to-eat food, install sneeze guards that intercept a direct line between the customer's mouth and the food being offered, dispense from approved mechanical dispensers, or employ other effective means to protect ready-to-eat food from contamination.
Protect all cartons, boxes, or other materials used in the packaging of any food from dirt, vermin, and other forms of contamination or adulteration.
(CDI) Observed the lids on the upper portion of the pizza prep fridges were taken off and placed on the ground near the oven. Keep the lids on and keep the food items covered when not under diligent preparation. All food items must be protected from possible contamination when not being used. 0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
2-20-2020 Wiping cloths used to wipe service counters, scales or other surfaces that may come into contact with food shall be used only once unless kept in clean water with sanitizer. (114135, 114185, 114185.1, 11485.2, 114185.3) 2.00 Cloths used to wipe service counters, scales, and other surfaces that may directly or indirectly contact food shall be used only once until laundered or may be used repeatedly if held in a sanitizing solution, as described below. Cloths used with raw foods of animal origin shall be used only once until laundered or may be used repeatedly if kept in a separate container of sanitizing solution, as described below:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with the manufacturer's use directions.
(REPEAT VIOLATION) Observed the sanitizer solution used to store wiping cloths was measured below 200PPM of quaternary ammonia. Be sure all sanitizer solution is at 200PPM minimum and changed frequently when turbid. 0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
2-20-2020 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 1.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method.
Observed the dish washing machine was not dispensing chlorine sanitizer of at least 50PPM. Dish washer was out of sanitizer solution and changed during inspection.

Observed the test strips at the facility were expired. Provide chlorine and quaternary ammonia test strips at all times to check sanitizer levels.
0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
2-20-2020 Potentially hazardous foods shall be held at or below 41°/ 45°F or at or above 135°F. (113996, 113998, 114037, 114343(a)) 7.00 Hold potentially hazardous foods either at or above 135°F or at or below 41°F. Hold the following potentially hazardous foods at 45°F: raw shell eggs, unshucked live molluscan shellfish, pasteurized milk and pasteurized milk products in original, sealed containers. Potentially hazardous foods held for dispensing in a serving line or a salad bar (not in a display case) may be held at 45°F or less during periods not to exceed 12 hours in any 24-hour period. Discard all potentially hazardous food that has been out of an approved time and temperature range. Observed the temperature of the salad bar items measured between 41F - 59F during inspection. Facility placed food items into the buffet/salad table and did not turn on the unit. Be sure to turn on the units and leave on at all times once food items are placed into the unit. All food items out of temperature by more than 10F were discarded during inspection.

Observed a tray of pre-made pizzas were measured at 53F - 59F during inspection. Keep all potentially hazardous food items at 41F and under or facility may implement a time control plan and must be approved by the inspector. All items that were 10F out of temperature were discarded during inspection.

0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
2-20-2020 All food employees shall have adequate knowledge of and be trained in food safety as it relates to their assigned duties. The person in charge shall have adequate knowledge of, and shall educate employees of the food facility regarding major food allergens. (113947) Food facilities that prepare, handle or serve non-prepackaged potentially hazardous food, shall have an employee who has passed an approved food safety certification examination. (113947-113947.1) 3.00 The responsibilities of the staff member certified in food safety include ensuring that all employees who handle, or have responsibility for handling, unpackaged foods of any kind have sufficient knowledge to ensure the safe preparation and /or service of the food. The nature and extent of the knowledge that each employee is required to have may be tailored, as appropriate, to the employee's duties related to food safety issues. Observed the lack of knowledge of proper dish washing methods. Proper dish washing methods were explained during inspection. Make sure to properly train all employees on proper dish washing techniques in case dish washer is out of commission.

0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
2-20-2020 All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182) 2.00 Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.

Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.

The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated.
(REPEAT VIOLATION) Observed a drain line inside the walk-in fridge that drains into a bucket inside the walk-in fridge. Repair so it is draining to a proper floor drain. There is currently a large bucket that is filled and dumped.

Observed build up of debris/grease on the deep fryer sides and equipment in this area. Clean/sanitize and increase frequency.
0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
2-20-2020 The walls / ceilings shall have durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair. (114065, 114067, 114069, 114175, 114143, 114257, 114259.2, 114266, 114268, 114268.1, 114271, 114272) 1.00 All food facilities shall be kept clean, fully operative, and in good repair. Floor surfaces in all areas in which food is prepared, packaged or stored, where any utensil is washed, where refuse or garbage is stored, where janitorial facilities are located, and in all restrooms and hand washing areas shall be smooth and of durable construction and made from non absorbent material that is easily cleanable.

Each permanent food facility shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. Food facilities that are not fully enclosed on all sides and that are in operation on January 1, 1985, shall not be required to meet the requirements of this section until the facility is remodeled or has a significant menu change or a change in its method of operation. Full enclosure is not required for dining areas and certain other areas when approved for outdoor food services.
Observed the flooring near the mens restroom is water damaged due to overflow of water from the floor sink under the three compartment sink. Repair/replace so it is smooth, flushed, and easily cleanable. 0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
2-20-2020 An accurate easily readable metal probe thermometer suitable for measuring temperature of food shall be available to the food handler. A thermometer +/- 2°F shall be provided for each hot and cold holding unit of potentially hazardous foods and high temperature warewashing machines. (114157, 114159) 1.00 Have a thermometer accurate to within 2°F or 1°C in each hot and cold holding unit. Have a metal probe type thermometer readily available on premises (to all appropriate staff) that is calibrated in accordance with the manufacturer's specifications as necessary to ensure accuracy. Observed a lack of thermometer in all fridge units. Keep a working thermometer in all fridge units that hold potentially hazardous food items.
0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
2-20-2020 Handwashing soap and single use towels or drying device shall be provided in dispensers adjacent to each handwashing facility; dispensers shall be maintained in good repair. (113953.2) Adequate separate facilities shall be provided for handwashing, food preparation, and the washing of utensils and equipment. (113953, 113953.1) 3.00 Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees. Employees shall not clean their hands in a sink used for food preparation, warewashing, or in a service sink or a curbed cleaning facility used for the disposal of mop water and similar liquid waste. Do not place objects in front of the handwashing station, and do not place items, utensils or wiping cloths in the handwashing sink.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Soap shall be provided in approved dispensers at, or adjacent to, handwashing facilities (no bars of soap). Single-use sanitary towels or hot-air blowers shall be provided at handwashing facilities in approved dispensing devices.
(CDI) Observed cups and other items inside the hand wash sinks in the front register and bar area. Keep all hand wash sinks clear at all times and only use for hand washing. Hand sinks were cleared during inspection.

Observed the hand wash sink in the bar area is not functioning properly. Repair or remove sink fixture. All hand wash sinks shall be stocked at all times for proper hand washing.
0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
2-20-2020 No violations were noted during this inspection. 0.00 This food facility currently meets California Retail Food Code requirements, and is authorized by the Merced County Division of Environmental Health to be open for business. The permit is issued to the current business owner of record and is non-transferable. All violations noted on 0102 report. 0123 BAR


Rating on date 1-04-2019: Satisfactory (Total Points: 12.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
1-04-2019 No violations were noted during this inspection. 0.00 This food facility currently meets California Retail Food Code requirements, and is authorized by the Merced County Division of Environmental Health to be open for business. The permit is issued to the current business owner of record and is non-transferable. No violations noted during inspection. 0123 BAR
1-04-2019 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 2.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method.
Observed a bucket used to catch the left over beer/ waste beer from the bar inside the walk-in fridge unit. Be sure to empty the bucket when ever needed (once a day if there is liquid inside). 0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
1-04-2019 All food employees shall have adequate knowledge of and be trained in food safety as it relates to their assigned duties. The person in charge shall have adequate knowledge of, and shall educate employees of the food facility regarding major food allergens. (113947) Food facilities that prepare, handle or serve non-prepackaged potentially hazardous food, shall have an employee who has passed an approved food safety certification examination. (113947-113947.1) 2.00 The responsibilities of the staff member certified in food safety include ensuring that all employees who handle, or have responsibility for handling, unpackaged foods of any kind have sufficient knowledge to ensure the safe preparation and /or service of the food. The nature and extent of the knowledge that each employee is required to have may be tailored, as appropriate, to the employee's duties related to food safety issues. Observed the lack of a current Food Manager certificate at the facility. Provide a Food Manager certificate within 60 days. Also observed the lack of food handler cards for all other employees. Provide a food handler card within 30 days for all other emlployees. 0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
1-04-2019 Handwashing signs shall be posted in each toilet room, directing attention to the need to thoroughly wash hands after using the restroom. (113953.5)

No smoking signs shall be posted in food preparation, food storage, and warewashing areas. (113978)

Consumers shall be notified that clean tableware is to be used when they return to self-service areas such as salad bars and buffets. (114075)

Any food facility constructed before January 1, 2004 without public toilet facilities shall prominently post a sign within the food facility in a public area stating that toilet facilities are not provided. (113725.1, 114276, 114381 (e))
2.00 Post permit in a conspicuous place (It is recommended that the permit be in customer view.). Post a notice advising patrons that a copy of the most recent routine inspection report is available for review by interested parties. Keep a copy of the most recent health inspection report at the facility for customer review purposes.

Post and maintain a legible and conspicuous sign in each toilet room directing attention to the need to thoroughly wash hands after using the toilet.

Post and maintain a legible "No Smoking" sign in food preparation, food storage, and utensil washing areas.

Observed the lack of knowledge of most recent inspection report. Keep a copy at the facility at all times. One was provided during the inspection. 0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
1-04-2019 Failure to keep food pure and free from contamination, adulteration and spoilage. Any food is adulterated if it bears or contains any poisonous or deleterious substance that may render it impure or injurious to health. (113967, 113976, 113980, 113988, 113990, 114035, 114254(c), 114254.3) 2.00 Provide adequate protection at all times to keep food pure and free from contamination, adulteration and spoilage. Destroy all contaminated, adulterated and spoiled food. Observed ground beef patties that were two weeks passed used by date. Packages indicated to be used or freeze by 12/18/18 and were still in use at the facility. Facility had received the burgers on 12/31/18. Be sure to check/inspect products before keeping when items are delivered. Burger patties were voluntarily discarded during inspection. 0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
1-04-2019 Handwashing soap and single use towels or drying device shall be provided in dispensers adjacent to each handwashing facility; dispensers shall be maintained in good repair. (113953.2) Adequate separate facilities shall be provided for handwashing, food preparation, and the washing of utensils and equipment. (113953, 113953.1) 2.00 Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees. Employees shall not clean their hands in a sink used for food preparation, warewashing, or in a service sink or a curbed cleaning facility used for the disposal of mop water and similar liquid waste. Do not place objects in front of the handwashing station, and do not place items, utensils or wiping cloths in the handwashing sink.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Soap shall be provided in approved dispensers at, or adjacent to, handwashing facilities (no bars of soap). Single-use sanitary towels or hot-air blowers shall be provided at handwashing facilities in approved dispensing devices.
Observed the hand wash sink nearest to the pizza prep unit being blocked by trash cans making it inaccesible. Keep the hand wash sink clear at all time. Trash cans were moved during the inspection.

Observed the lack of paper towels at the hand wash station nearest to the deep fryer. Provide paper towels in approved dispensers at all times for proper hand washing.
0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS
1-04-2019 Wiping cloths used to wipe service counters, scales or other surfaces that may come into contact with food shall be used only once unless kept in clean water with sanitizer. (114135, 114185, 114185.1, 11485.2, 114185.3) 2.00 Cloths used to wipe service counters, scales, and other surfaces that may directly or indirectly contact food shall be used only once until laundered or may be used repeatedly if held in a sanitizing solution, as described below. Cloths used with raw foods of animal origin shall be used only once until laundered or may be used repeatedly if kept in a separate container of sanitizing solution, as described below:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with the manufacturer's use directions.
Observed the sanitizer solution for the buckets measured at 0PPM. Sanitizer solution was renewed during inspection. Make sure sanitizer solution is at 200PPM for Quaternary Ammonia. Use test strips to verify. 0102 FOOD ESTAB. W/FOOD PREP 50-149 SEATS