4-30-2021 |
Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125)
| 2.00 |
Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.
Clean the utensils in one of the following ways:
(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following: (a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above. (b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions: (1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds. (2) Contact with a solution of 25 ppm available iodine for at least one minute. (3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute. (4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6. (c) Other methods approved by the enforcement agency.
(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following: (a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above. (b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following: (1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds. (2) Contact with a solution of 25 ppm available iodine for at least one minute. (3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.
Provide testing equipment and materials to adequately measure the applicable sanitization method.
|
REPEAT: Observed lack of the correct type of 'usable' test strips to measure the applicable manual sanitizer concentration in use (damaged pack of test strips present, appear they may have been dropped in liquid). Obtain and use matching test strips for the sanitizer on site to verify sanitizer is of sufficient strength to act as an appropriate manual sanitizing agent when used (200 PPM for 60 seconds of contact time for quat ammonia).
|
0122 CAFETERIA [SCHOOL]
|
4-30-2021 |
All utensils and equipment shall be fully operative, clean, and in good repair. (114115, 114175). All utensils and equipment shall be approved, installed properly, and meet applicable standards. (114130, 114130.1, 114130.2, 114130.3, 114130.4, 114130.5, 114130.6, 114132, 114133, 114137, 114139, 114143, 114153, 114155, 114163, 114165, 114167, 114169, 114172, 114175, 114177, 114180, 114182)
| 1.00 |
Equipment food-contact surfaces and utensils shall be clean to sight and touch. The food-contact surfaces of cooking equipment and pans shall be kept free of encrusted grease deposits and other debris accumulations.
Keep all food facilities, and all utensils, display cases, windows, counters, shelves, tables, refrigeration units, sinks, dishwashing machines, and other equipment or utensils used in the storage, preparation, sale, service, and display of food, clean, fully operative, and in good repair.
The non-food-contact surfaces of equipment shall be kept free of an accumulation of dust, dirt, food residue, and other debris. Equipment shall be reassembled so that food-contact surfaces are not contaminated.
|
Observed protective shipping film still present / left on stainless steel surfaces of thermo hot box unit at this site. Film is peeling at the edges, sticky residue, scratched and gouged, small chunks coming off near the edges / corners. Remove the shipping film. The shipping film does not constitute a smooth, easily cleanable, and durable commercial grade surface. Do not render equipment or storage surfaces difficult to properly clean and sanitize. Film immediately peeled off unit. Be sure these surfaces are cleaned and sanitized on a regular basis so they are not an unintentional source of potential cross contamination. Corrected during inspection.
|
0122 CAFETERIA [SCHOOL]
|