| 5-08-2023 |
Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125)
| 1.00 |
Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.
Clean the utensils in one of the following ways:
(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.
(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.
Provide testing equipment and materials to adequately measure the applicable sanitization method.
|
Observed lack of test strips to measure the applicable manual sanitizer concentration. Obtain and use test strips to verify sanitizer is of sufficient strength to act as an appropriate manual sanitizing agent (100 ppm for chlorine, 200 ppm for quat ammonia).
|
0105 LICENSED HEALTH CARE FAC.(100-199 BEDS)
|
| 5-08-2023 |
The potable water supply shall be protected with a backflow or back siphonage protection device, as required by applicable plumbing codes. (114192) All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair. Any hose used for conveying potable water shall be of approved materials, labeled, properly stored, and used for no other purpose. (114171, 114189.1, 114190, 114192.1, 114193, 114193.1, 114195, 114197, 114199, 114201, 114269)
| 1.00 |
All plumbing and plumbing fixtures shall be installed in compliance with local plumbing ordinances, shall be maintained so as to prevent any contamination, and shall be kept clean, fully operative, and in good repair.
|
Observed a leak at the prep sink where the hot water handle is, water was leaking while the sink was not being used. Please fix to ensure all fixtures are in good condition and repair.
|
0105 LICENSED HEALTH CARE FAC.(100-199 BEDS)
|