Return To Restaurant Listing | Return to Environmental Health Homepage

Facility: Bobbi's Food Corner
Address: 1401 Atwater Blvd, Atwater, CA

The most recent inspection of this food facility resulted in a rating of
Good (Total Points: 1.00)
0-6  Points: Good
7-13 Points: Satisfactory
14+  Points: Unsatisfactory
Rating on date 4-26-2022: Good (Total Points: 1.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
4-26-2022 An accurate easily readable metal probe thermometer suitable for measuring temperature of food shall be available to the food handler. A thermometer +/- 2°F shall be provided for each hot and cold holding unit of potentially hazardous foods and high temperature warewashing machines. (114157, 114159) 1.00 Have a thermometer accurate to within 2°F or 1°C in each hot and cold holding unit. Have a metal probe type thermometer readily available on premises (to all appropriate staff) that is calibrated in accordance with the manufacturer's specifications as necessary to ensure accuracy. Observed a thermometer had been placed inside the hot holding box/unit, however the thermometer started at a low of 150F. Obtain a thermometer with a smaller/lower starting range. 0110 RETAIL MARKET<2000 SQ FT (HM3)


Rating on date 3-24-2022: Unsatisfactory - reinspection required (Total Points: 19.00)
DateViolationPointsCorrectionInspector CommentsFacility Area
3-24-2022 Potentially hazardous foods shall be held at or below 41°/ 45°F or at or above 135°F. (113996, 113998, 114037, 114343(a)) 7.00 Hold potentially hazardous foods either at or above 135°F or at or below 41°F. Hold the following potentially hazardous foods at 45°F: raw shell eggs, unshucked live molluscan shellfish, pasteurized milk and pasteurized milk products in original, sealed containers. Potentially hazardous foods held for dispensing in a serving line or a salad bar (not in a display case) may be held at 45°F or less during periods not to exceed 12 hours in any 24-hour period. Discard all potentially hazardous food that has been out of an approved time and temperature range. (CDI) Observed the temperature of the prepackaged burritos and hot pockets in the hot holding unit was measured between 111F - 122F during the inspection. Keep all potentially hazardous food items at 41F and under or 135F and over. All food items that were out of temperature range by 10F or more was discarded during the inspection. 0110 RETAIL MARKET<2000 SQ FT (HM3)
3-24-2022 Handwashing signs shall be posted in each toilet room, directing attention to the need to thoroughly wash hands after using the restroom. (113953.5)

No smoking signs shall be posted in food preparation, food storage, and warewashing areas. (113978)

Consumers shall be notified that clean tableware is to be used when they return to self-service areas such as salad bars and buffets. (114075)

Any food facility constructed before January 1, 2004 without public toilet facilities shall prominently post a sign within the food facility in a public area stating that toilet facilities are not provided. (113725.1, 114276, 114381 (e))
1.00 Post permit in a conspicuous place (It is recommended that the permit be in customer view.). Post a notice advising patrons that a copy of the most recent routine inspection report is available for review by interested parties. Keep a copy of the most recent health inspection report at the facility for customer review purposes.

Post and maintain a legible and conspicuous sign in each toilet room directing attention to the need to thoroughly wash hands after using the toilet.

Post and maintain a legible "No Smoking" sign in food preparation, food storage, and utensil washing areas.

Observed the lack of a posted hand wash notice in the restroom. Provide a posted notice at all times to remind employees to wash their hands after visiting the restroom. 0110 RETAIL MARKET<2000 SQ FT (HM3)
3-24-2022 All food employees shall have adequate knowledge of and be trained in food safety as it relates to their assigned duties. The person in charge shall have adequate knowledge of, and shall educate employees of the food facility regarding major food allergens. (113947) Food facilities that prepare, handle or serve non-prepackaged potentially hazardous food, shall have an employee who has passed an approved food safety certification examination. (113947-113947.1) 3.00 The responsibilities of the staff member certified in food safety include ensuring that all employees who handle, or have responsibility for handling, unpackaged foods of any kind have sufficient knowledge to ensure the safe preparation and /or service of the food. The nature and extent of the knowledge that each employee is required to have may be tailored, as appropriate, to the employee's duties related to food safety issues. Observed the lack of a valid food handler card at the facility and the facility engages in prepackaging ice and heating frozen burritos. Provide a valid food handler card in 30 days. 0110 RETAIL MARKET<2000 SQ FT (HM3)
3-24-2022 Food facilities that prepare food shall be equipped with warewashing facilities. Testing equipment and materials shall be provided to measure the applicable sanitization method. (114067(f,g), 114099, 114099.1, 114099.2, 114099.3, 114099.4, 114099.5, 114099.6, 114099.7, 114101, 114101.1, 114101.2, 114103, 114107, 114125) 1.00 Provide a sink with at least 3 compartments with 2 integral metal drainboards. The sink compartments and drainage facilities shall be large enough to accommodate the largest utensil or piece of equipment to be cleaned therein.

Clean the utensils in one of the following ways:

(1) Manual warewashing shall be accomplished by using a 3-compartment sink where the utensils are first pre-cleaned, then washed, rinsed, sanitized, and air dried. The temperature of the washing solution shall be maintained at not less than 100°F or the temperature specified on the cleaning agent manufacturer's label instructions. The utensils shall then be rinsed in clear water before being immersed in a sanitizing solution. Manual sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) Immersion for at least 30 seconds where the water temperature is maintained at 171°F or above.
(b) The application of sanitizing chemicals by immersion, manual swabbing, or brushing, using one of the following solutions:
(1) Contact with a solution of 100 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with a solution of 200 ppm quaternary ammonium for at least one minute.
(4) Contact with a solution of ozone that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations and that is generated by a device located onsite at the food facility that meets all of the requirements of 114099.6.
(c) Other methods approved by the enforcement agency.

(2) Mechanical machine warewashing shall be accomplished by using an approved machine installed and operated in accordance with the manufacturer's specifications. Soiled items to be cleaned in a warewashing machine shall be loaded in racks, trays, or baskets or onto conveyors in a position that exposes the items to the unobstructed spray during all cycles and allows the items to drain. Mechanical sanitization shall be accomplished in the final sanitizing rinse by one of the following:
(a) By being cycled through equipment achieving a utensil surface temperature of 160°F or above.
(b) The mechanical application of sanitizing chemicals by pressure spraying methods using one of the following:
(1) Contact with a solution of 50 ppm available chlorine solution for at least 30 seconds.
(2) Contact with a solution of 25 ppm available iodine for at least one minute.
(3) Contact with any chemical sanitizer that meets the requirements of Section 180.940 of Title 40 of the Code of Federal Regulations when used in accordance with both the sanitizer manufacturers use directions and the machine manufacturer's specifications.

Provide testing equipment and materials to adequately measure the applicable sanitization method.
Observed lack of chlorine test strips to measure the applicable manual sanitizer concentration. Obtain and use test strips to verify sanitizer is of sufficient strength to act as an appropriate manual sanitizing agent (100 ppm for chlorine, 200 ppm for quat ammonia). 0110 RETAIL MARKET<2000 SQ FT (HM3)
3-24-2022 The walls / ceilings shall have durable, smooth, nonabsorbent, light-colored, and washable surfaces. All floor surfaces, other than the customer service areas, shall be approved, smooth, durable and made of nonabsorbent material that is easily cleanable. Approved base coving shall be provided in all areas, except customer service areas and where food is stored in original unopened containers. Food facilities shall be fully enclosed. All food facilities shall be kept clean and in good repair. (114065, 114067, 114069, 114175, 114143, 114257, 114259.2, 114266, 114268, 114268.1, 114271, 114272) 1.00 All food facilities shall be kept clean, fully operative, and in good repair. Floor surfaces in all areas in which food is prepared, packaged or stored, where any utensil is washed, where refuse or garbage is stored, where janitorial facilities are located, and in all restrooms and hand washing areas shall be smooth and of durable construction and made from non absorbent material that is easily cleanable.

Each permanent food facility shall be fully enclosed in a building consisting of permanent floors, walls, and an overhead structure that meets minimum standards. Food facilities that are not fully enclosed on all sides and that are in operation on January 1, 1985, shall not be required to meet the requirements of this section until the facility is remodeled or has a significant menu change or a change in its method of operation. Full enclosure is not required for dining areas and certain other areas when approved for outdoor food services.
Observed the flooring near the restroom/back room entrance is damaged and has risen up. Repair/replace so it is flushed, smooth, and easily cleanable. 0110 RETAIL MARKET<2000 SQ FT (HM3)
3-24-2022 Handwashing soap and single use towels or drying device shall be provided in dispensers adjacent to each handwashing facility; dispensers shall be maintained in good repair. (113953.2) Adequate separate facilities shall be provided for handwashing, food preparation, and the washing of utensils and equipment. (113953, 113953.1) 3.00 Handwashing facilities shall be sufficient in number and conveniently located so as to be accessible at all times for use by food employees. Employees shall not clean their hands in a sink used for food preparation, warewashing, or in a service sink or a curbed cleaning facility used for the disposal of mop water and similar liquid waste. Do not place objects in front of the handwashing station, and do not place items, utensils or wiping cloths in the handwashing sink.

Handwashing facilities shall be equipped to provide warm water under pressure for a minimum of 15 seconds. If the temperature of water provided is not readily adjustable at the faucet, the temperature of the water shall be at least 100°F, but not greater than 108°F. Soap shall be provided in approved dispensers at, or adjacent to, handwashing facilities (no bars of soap). Single-use sanitary towels or hot-air blowers shall be provided at handwashing facilities in approved dispensing devices.
Observed the hand wash sink in the the utensil washing area was blocked by return for credit items. Keep the hand wash sink clear at all times for hand washing. Move items and allow for access to the hand wash sink for hand washing. 0110 RETAIL MARKET<2000 SQ FT (HM3)
3-24-2022 Any food is misbranded if its labeling is false or misleading, if it is offered for sale under the name of another food, or if it is an imitation of another food for which a definition and standard of identity has been established by regulation. (114087, 114089, 114089.1(a, b), 114090, 114093.1, 114377) 1.00 Present all food in a way that does not mislead or misinform consumers. Food or color additives, colored overwraps, lights or other misleading artificial means shall not be used to misrepresent the true appearance, color, or quality of a food.

The label shall contain the following information:
(1) The common name of the food.
(2) A list of ingredients in descending order of predominance by weight.
(3) The weight, count, or volume.
(4) The name and place of business of the manufacturer, packer, or distributor.
Nutrition labeling may also be required, and must be included when it is available from the manufacturer.

Food facility's or manufacturer's dating information, such as date codes or "use by" statements on packaging may not be concealed or altered.
Observed prepackaged bags of ice that are packaged at the facility were lacking proper labels on the bags of ice. Provide on all prepackaged bags of ice that are packaged at the facility. 0110 RETAIL MARKET<2000 SQ FT (HM3)
3-24-2022 Exhaust hoods shall be provided to remove toxic gases, heat, grease, vapors, and smoke and be approved by the local building department. Canopy-type hoods shall extend 6" beyond all cooking equipment. All areas shall have sufficient ventilation to facilitate proper food storage. Toilet rooms shall be vented to the outside air by a screened openable window, an air shaft, or a light-switch activated exhaust fan, consistent with local building codes. (114149, 114149.1) Adequate lighting shall be provided in all areas to facilitate cleaning and inspection. Light fixtures in areas where open food is stored, served, prepared, and where utensils are washed shall be of shatterproof construction or protected with light shields. (114149.2, 114149.3, 114252, 114252.1) 1.00 All areas shall have sufficient ventilation to facilitate proper food storage and to provide a reasonable condition of comfort for each employee, consistent with the job performed by the employee.

Light fixtures in areas where food is prepared, open food is stored, or utensils are cleaned shall be of shatterproof construction or shall be protected with shatterproof shields and shall be readily cleanable. In every room and area in which any food is prepared, manufactured, processed, or prepackaged, or in which equipment or utensils are cleaned, sufficient natural or artificial lighting shall be provided to produce the following light intensity, while the area is in use:
(a) At least 10-foot candles for the following:
(1) At a distance of 30 inches above the floor, in walk-in refrigeration units, and dry food storage areas.
(2) At a working surface on which alcoholic beverages are prepared or where utensils used in the preparation or service of alcoholic beverages are cleaned.
(3) Inside equipment, such as reach-in or under-the-counter refrigerators.
(b) At least 20-foot candles for the following:
(1) At a surface where food is provided for consumer self-service or where fresh produce or prepackaged foods are sold or offered for consumption.
(2) In server stations where food is prepared.
(3) At a distance of 30 inches above the floor in areas used for handwashing, warewashing, and equipment and utensil storage, and in toilet rooms.
(c) Except in server stations where food is prepared, at least 50-foot candles at a surface where a food employee is working with food or working with utensils or equipment such as knives, slicers, grinders, or saws where employee safety is a factor.
Observed the light fixture in / over the walk-in fridge unit does not function, bulb may be burned out. Replace bulb and / or repair fixture. Failure to provide adequate lighting. 0110 RETAIL MARKET<2000 SQ FT (HM3)
3-24-2022 An accurate easily readable metal probe thermometer suitable for measuring temperature of food shall be available to the food handler. A thermometer +/- 2°F shall be provided for each hot and cold holding unit of potentially hazardous foods and high temperature warewashing machines. (114157, 114159) 1.00 Have a thermometer accurate to within 2°F or 1°C in each hot and cold holding unit. Have a metal probe type thermometer readily available on premises (to all appropriate staff) that is calibrated in accordance with the manufacturer's specifications as necessary to ensure accuracy. Observed the lack of a valid thermometer in the hot holding unit and in the small fridge unit that holds prepackaged sandwiches. Provide a thermometer accurate to within 2ºF or 1ºC in each refrigeration and hot holding unit, as practicable. Note that product mimicking sensors placed in devices located in the warmest part of the mechanically refrigerated unit may be approved in lieu of an ambient air sensor. 0110 RETAIL MARKET<2000 SQ FT (HM3)